Office Tape Slitter Machine

Office Tape Slitter Machine

Tape slitting machine feeding, filming and filming
1. Loading: According to the requirements of the cutting plan, according to the driving operation rules, according to the actual situation, hoist the corresponding mother roll on the aging frame, place it on the unwinding unwinding frame according to the inner and outer selection direction of the corona surface, and use the control button Clamp the steel core, leave the steel core support arm and drive.
2. Film penetration: When there is no film on the slitter, the film must be penetrated. Using the slitting machine through the membrane device and the function keys, one end of the original membrane is attached to the membrane chain eyelet, and the membrane button is activated to distribute the membrane along the slitting process to be evenly distributed on each roller.
3. Film: When there is a film on the slitter, when changing the joint, use the vacuum filming table to start the filming station to the working position, manually flatten the film on the first pulling roller of the slitting machine and start the upper vacuum pumping film. Soak the film flat on the filming table, attach the double-sided tape and cut off the excess film under the tape, flatten the film on the unwinding frame and start the lower vacuum pump to make the film flat and absorb the paper. Layer and flatten the adhesive film, the joints should be neat and wrinkle-free, then turn off the upper and lower vacuum pumps to open the filming station to the inoperative position.

Office Tape Slitter Machine

Main factors affecting tension stability:
(1) The change of the speed of the machine will inevitably cause the change of the tension of the whole machine.
(2) During the process of collecting and unwinding, the winding and unwinding diameters of the slitting machine are constantly changing, and the change of the diameter will inevitably cause the change of the material tension. When the unwinding torque is constant, the diameter is reduced and the tension is increased. The winding is reversed. If the winding torque is constant, the tension will decrease as the winding diameter increases. This is the main factor that causes the change in material tension during operation.
(3) The change in the tightness of the raw material roll will also cause a change in the tension of the whole machine.
(4) The unevenness of the material of the raw material is cut. If the material elasticity fluctuates, the material thickness changes along the width and length direction, the mass of the material roll is eccentric, and the temperature and humidity of the production environment change, which also affects the tension fluctuation of the whole machine.
(5) The various transmission mechanisms (such as guide rollers, floating rollers, flattening rollers, etc.) of the slitting machine have factors such as imbalance and unstable air pressure.

Office Tape Slitter Machine

Slitting machine operating procedures -

First. When the unwinding machine normally replaces the parent roll
1. The machine is wound up and the machine speed is zero. Press the "machine off" button and all drives are turned off.
2. Press and hold the “core release” button to make the chuck exit the empty core, the empty core is placed on the unloading guide, and then the pneumatic ejector will automatically
Empty the core to the unloading position, release the button, and the steel core is to be transported away by the crane.
3. Press the “Coil Snap” button briefly to retract the cylinder rod at the unwinding position to the receiving position.
4. According to the plan, attach the corresponding mother roll to the double-sided tape, and hang the new mother roll into the V-shaped support that supports the parent roll, and hang the empty roll.
core.
5. Press and hold the “Coil Core Clamp” button to make the card head into the new parent roll until the card head positioning pin is in place and release the button. 6. Adjust the length and diameter of the unwinder on the operation screen (correct the input value if necessary), and replace the parent roll.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com