Fabric Rolling Machine

Fabric Rolling Machine

Rewinding Machine operating procedures - Start thread
1The main operator passes the inspection to confirm that the paper core and the size of the paper cut are correct.
The power-on signal informs the operator to prepare the paper. Open the paper feed roller, blower system, and paper positioning system before threading.
2. Start the rewinding machine and crawl the car at a speed of 15 meters.
3. The base paper is torn or folded into a triangle and sent to the platen roller to be delivered by the platen roller.
The paper is fed to the bottom knife roll and pressed against the horizontal roller.
4. The paper web is drawn flat and the paper trimming is aligned with the paper core and the port.
Introduce the paper edge fan to inform the main operation to stop. At this time, check the trimming situation and adjust it in time.
5. Use a piece of tape to match the paper web to the paper core, and then remove the letter immediately after sticking.
No. To inform the main operation, press the platen roller button to press the platen roller against the paper core, and start the roll paper.

Fabric Rolling Machine

Rewinding Machine operation safety regulations - 

Second, the operation steps:

7. When the layers of paper are completely flat and enter the rewinding, the waste coils are taken out to the normal production state. 8, check the production situation:
(1) Check whether the two ends of the base paper are symmetrical. For example, the auger can adjust the auger on the unloading frame to the ends of the paper. (2) Check whether the punched paper is clear, the punching is not clear or the missing teeth are checked. Whether the knife is broken or not
Whether the wire is loose, adjust the height of the bottom knife, and mass production after inspection;
(3) Check whether the paper feeding tension of the rewinding paper is consistent, keep the paper surface flat and no wrinkles, such as inconsistency
Then adjust the paper return belt hand wheel on the paper exit frame;
(4) Check whether the paper between the embossing stick and the winding area is flat and tight, if it meets the requirements, if it does not meet the requirements,
Then adjust the gearbox handwheel (when adjusting the gearbox handwheel, you can't stop the adjustment, you need to turn it on slowly); (5) Check whether the semi-finished paper roll is tight, the diameter and weight meet the product standard requirements, and the two ends are neat (straight
The deviation of the diameter shall not exceed ±1mm, and the weight deviation shall be within ±2);
(6) Whether the width of the glue seal of the paper ball meets the standard (package standard is 10mm-15mm), the penetration of glue
No more than 3 single-layer papers;
(7) Do not arbitrarily tamper with the inverter, programmed wiring and settings in the electric box; (8) Non-operator operators must not let the machine operate without the consent of the supervisor;

Third,. After the above steps are checked normally, Slowly speed up to normal operation.

Fabric Rolling Machine

Rewinding Machine operation safety regulations - 

Fifth, machine maintenance and hygiene
1. After the production is completed, first adjust the governor to zero, close the program switch, and finally turn off the power of the control box;
2. Use the air duct to blow the inside and outside of the machine and the electric box, and do not place any debris such as tools in the machine and the electric box.
3. Regularly repair and maintain the rotating parts of the machine (add some amount of oil or butter)
4. The hygiene of the machine area must be cleaned.
5. The waste paper is sent to the pulping station of the designated paper mill. The original paper core is neatly stacked in the specified paper barrel stacking area according to the specifications. The leather tape, waste paper and waste paper core are placed in the designated stacking area.
6, with the machine repair to do the regular maintenance of the machine main maintenance work.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com