Minitape Cutter Machine

Minitape Cutter Machine

Tape Cutting Machine-

Third, pay attention to the operation process:
1. The torch is in contact with the workpiece and can be cut by pressing the button. Cutting can be started from the edge of the workpiece. When the thickness of the sheet is not large, it can be cut at any point of the workpiece. The torch can be perpendicular to the workpiece
Or slightly inclined to one side, but when opening in the middle of the workpiece, the torch should be tilted slightly to one side in order to blow off the molten metal and cut through the metal.
2. Press the handle button and keep the main circuit on, while the high frequency oscillator works until the cutting arc is formed, and the high frequency oscillator stops working. Thereafter, the cutting can be performed by the movement of the torch. At the same time, the cutting indicator lights.
3. The cutting must be cut through the metal to move evenly, otherwise the nozzle will be damaged. Moving too fast or too slow will affect the quality of the cut.
4, cutting air pressure adjustment: cutting air pressure is too high, the flow is too large, will affect the cutting thickness. If the cutting air pressure is too small, it will affect the service life of the nozzle.
5. Before lifting the torch away from the workpiece, the handle button must be turned on. At this time, the plasma arc is extinguished and the cutting process is stopped.
6. During the cutting process, the arc is re-arced because the torch leaves the workpiece more than 2 mm and the arc is extinguished.
7. When the main transformer temperature exceeds 110 °C due to the connection working time is too long, the thermal protection switch will operate and the device will automatically shut down and cannot be started. It should be restarted after the transformer has cooled down.
8. Always remove the accumulated water in the filter pressure reducing valve, that is, rotate the lowermost screw counterclockwise to remove the water and then tighten. If there is too much water in the compressed air, consider adding a filter valve between the filter pressure reducing valve and the gas source, otherwise the cutting quality will be affected.
9. When the workpiece is not cut, press the torch button as little as possible to avoid damage to the machine.
10. After the cutting workpiece is finished, cut off the power switch and the air supply valve.

Minitape Cutter Machine

Tape Cutting Machine - related instructions

The tape cutting machine is also a tape machine, which is an indispensable small auxiliary mechanical device for most production lines, but there is no specific explanation for the technical operation. The following is a description based on the operation of the tape cutting machine. The operation of the tape cutter is different from that of the disc tape cutter, because they are different tape cutter models, and the shape is also very different. This tape cutter is ready to cut, if cut. If the tape is not removed in time, the tape cutter will stop cutting until the cut tape is removed, which is more flexible.
The tape cutter has a large knife edge, so you can cut all the tapes within the width range, and you can cut two tapes with a small width at the same time (the width is added to the tape cutter parameters).

Minitape Cutter Machine

Tape Cutting Machine - related instructions

         The tape cutting machine has a counting and cutting length setting function. When using it, the tape should be placed in the tape cutting machine. The tape head should be pulled, then the power is turned on, the switch is turned on, and the setting is set according to the requirements. After that, press the yellow button on the right (start button), and the tape cutter starts to run and cut.
         The tape cutter cuts only a piece of tape at a time, and the cut tape is spit out at the gate. The sensor is installed at the gate. If the tape is not removed, the tape cutter will always be in a stagnant state. When we remove the tape, the tape The cutter will start automatically and cut the next tape. Cycle back and forth.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com