Name Tape Cutter

Name Tape Cutter

Tape Cutting Machine-

Third, pay attention to the operation process:
1. The torch is in contact with the workpiece and can be cut by pressing the button. Cutting can be started from the edge of the workpiece. When the thickness of the sheet is not large, it can be cut at any point of the workpiece. The torch can be perpendicular to the workpiece
Or slightly inclined to one side, but when opening in the middle of the workpiece, the torch should be tilted slightly to one side in order to blow off the molten metal and cut through the metal.
2. Press the handle button and keep the main circuit on, while the high frequency oscillator works until the cutting arc is formed, and the high frequency oscillator stops working. Thereafter, the cutting can be performed by the movement of the torch. At the same time, the cutting indicator lights.
3. The cutting must be cut through the metal to move evenly, otherwise the nozzle will be damaged. Moving too fast or too slow will affect the quality of the cut.
4, cutting air pressure adjustment: cutting air pressure is too high, the flow is too large, will affect the cutting thickness. If the cutting air pressure is too small, it will affect the service life of the nozzle.
5. Before lifting the torch away from the workpiece, the handle button must be turned on. At this time, the plasma arc is extinguished and the cutting process is stopped.
6. During the cutting process, the arc is re-arced because the torch leaves the workpiece more than 2 mm and the arc is extinguished.
7. When the main transformer temperature exceeds 110 °C due to the connection working time is too long, the thermal protection switch will operate and the device will automatically shut down and cannot be started. It should be restarted after the transformer has cooled down.
8. Always remove the accumulated water in the filter pressure reducing valve, that is, rotate the lowermost screw counterclockwise to remove the water and then tighten. If there is too much water in the compressed air, consider adding a filter valve between the filter pressure reducing valve and the gas source, otherwise the cutting quality will be affected.
9. When the workpiece is not cut, press the torch button as little as possible to avoid damage to the machine.
10. After the cutting workpiece is finished, cut off the power switch and the air supply valve.

Name Tape Cutter

Automatic tape cutting machine tape machine - Detailed introduction
1: Press the switch button to cut the adhesive tape, half a turn around the turntable.
2: The cutting distance is adjustable.
3: The unique conveyor system makes it easier to pick up than the edge of the turntable.
4: Small adhesive tape for use on the board.
5: The emission interval can be adjusted according to the bandwidth.
6: Various adhesive tapes can be cut and the incision is sharp.
7: Using a dedicated base, the outer diameter of the tape can reach 170mm
Cutting size 13-60mm
Tape width 3-25mm
specification:
Size: 300w*165h-170d MM;
Cutting size: 13-60MM;
Tape width: 3-25MM;
Reel size: inner diameter 25-32-75MM, outer diameter: Up to 130mm;
Weight: 3kg
Applicable tape: vinyl tape, polyester film tape, polyethylene tape, acetate base tape, cellophane, masking tape, plain paper, glass cloth tape, aluminum foil tape, cotton tape, double-sided tape, etc.;
Power requirements: AC100V, 120V, 220±20VM 50-60HZ, 160W;

Name Tape Cutter

Guolian tape cutting machine GL-704 parameters:


LED directly displays size data;
Box-shaped cutting parts and replacement, saving time and effort, automation, high efficiency;
The tape has no trace, the slit is flat, and it is automatically cut off after automatic feeding. It is free to press the switch, cut the length of 20-999mm), set it arbitrarily, and automatically send the tape to cut.
specification:
Adhesive paper width: 7-50MM;
Applicable adhesive tape inner diameter: 25.32.75mm;
Adhesive paper set length: 20-999mm;
Size: 137*245*150mm;
Power: 18w;
Weight: 2.4kg;
Power supply: AC220V 50Hz.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com