Instructions for the operation of the tape cutter.
The tape cutter is operated differently than the disc tape cutter, because they are different tape cutter models, and the shape is also very different. This tape cutter is ready to cut.
If the cut tape is not removed in time, the tape cutter will stop cutting until the cut tape is removed, which is more flexible.
The tape cutter has a large knife edge, so you can cut all the tapes within the width range, and you can cut two tapes with a small width at the same time (the width is added to the tape cutter parameters).
The tape cutting machine has a counting and cutting length setting function. When using it, the tape should be put into the tape cutting machine, the tape head should be pulled, then the power is turned on, and the switch is turned on.
Set according to the requirements, press the yellow button (start button) on the right after setting, the tape cutting machine starts to run and cut. The tape cutter cuts only a piece of tape at a time, and spits the cut tape out at the gate.
The sensor is installed at the gate. If the tape is not removed, the tape cutter will remain in a stagnant state. When we remove the tape, the tape cutter will automatically start and cut the next tape. Cycle back and forth.
GL-704B Four-shaft Auto Roll Cutting Machine, Suitable for cutting BOPP tape, PVC insulation tape, masking tape, double sided tape, duct tape, medical tape, etc.
1. Main driving part: Siemens AC motor with inverter is employed.
2.Operating panel part: All functions are operated on the 10" LCD touch panel.
3. Motor control system: The central control system is PLC programmable controller.
4. Quick shaft change system: Three kinds of shafts are available and quick change of shafts is applied for different materials.
5. Central control unit: Programmable central control is used and 20 sizes can be set on the same shaft for auto transfer and cutting.
6. Blade feeding positioning system: Blade feeding is controlled by Mitsubishi servo motor, and the cutting speed is adjustable in three stages.
7. Auto exchange device: Cylinder-driven position spline gear is used to ensure fast & precise exchange; non-stop machine to save material loading & unloading time and improve efficiency.
8. Cutting positioning system: Cutting positioning is controlled by Mitsubishi servo motor. The imported high precision ball screw is applied to set the size and the linear slide rail is to bear the load of the cutter seat.
9. Auto angle adjustment of circular blade: Mitsubishi servo motor is used to calculate the circular blade angle and the angle change is subject to different materials (the angle change range is ±8°).
Tape cutting machine features ---
1. The tape cutting machine adopts no roller design, which is convenient for operation.
2, the maximum width of the cutting is 60mm (see machine parameters below), this must be understood before use, to see if it meets the width of the tape you want to cut.
3, tape cutting machine with memory function, according to the length of the tape cut usually from the set of six different cutting lengths, you can call directly after the need to set up.
4, install the tape, through the elastic film auxiliary shaft, so it is easier to fix the film to prevent the tape roll from falling.
5, tape cutting machine with counting function, you can set the amount to be cut.
6. Two rolls of tape can be used at the same time, but the total width should be within the width parameter of the tape cutter.
7. Be careful when taking the tape. Although the tape cutter is equipped with a protective device and a safety guard at the knife edge, try not to approach the knife edge.
8, accurate digital control cutting length, you can set the length you want to cut.
9. It is not necessary to adjust the tape cutter because of the thickness of the tape.
10. The tape cutting machine has built-in pliers, lubricating oil and partition for easy operation.
11, anti-static ABS material
12. Improve safety. When the warning device is operated and the tape cutter is suspended, even if the blockage is removed, the tape cutter will not operate immediately. You need to press the start button again to use it normally.
Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc