Label Paper Making Machine

Label Paper Making Machine

The rewinder is a special equipment for mica tape and film. The rewinding process mainly accomplishes three tasks: first, cutting off the raw paper burrs; second, cutting the whole original paper into 
a plurality of widths in accordance with user specifications; Third, control the winding diameter of the finished paper roll to meet the factory specifications.

 

Advantages of the winder
1, equipped with processing unintentional, solid, paper tube toilet paper, can instantly switch between products. 2, automatic trimming, glue spraying, sealing, and the shaft is instantaneously synchronized, so that the paper is transferred into the band saw and the paper is not damaged when it is cut.
3. Pneumatic belt feeding, double reel and each axis of the original paper have independent tension adjustment mechanism.

Label Paper Making Machine

Rewinder mechanical structure and control process ---

 

Second, the main structure of the winder

2.2 Longitudinal section
In the mechanical system of the winder, the slitting mechanism is a very important part of the winder. In order to ensure a straight and smooth cutting edge, the quality control of the finished paper roll plays an important role in ensuring the volume. It is easy and can reduce the fluffing during printing. The slitting mechanism should be installed as close as possible to the paper roll so that it can produce a lateral movement more than necessary during the process of cutting the web without curling.
The high-speed rewinding paper conveying system is also very important in the application. The old-fashioned rewinding machine is mainly handled by manual. With the increase of the speed of the rewinding machine, the manual can no longer be processed. There are two ways to transport the paper side of the reel: fan direct pumping and venturi suction. The direct drawing type of the fan mainly uses a centrifugal fan, and the fan is placed under the floor. The inlet of the fan and the air duct near the longitudinal cutting edge are connected to each other, and the blade of the fan is also equipped with a wind blade. When the fan is sucked, it will be broken by the blade and then sent to the water pulper. However, since the edge of the paper has to pass through the inside of the fan, the blade transported by this type of paper is very worn and needs to be changed frequently. Venturi suction is also used in the high-pressure centrifugal fan, but the paper edge does not pass through the fan, directly the longitudinal cutting edge of the duct into the venturi pipe, the wind machine generates negative pressure in the venturi, and then the paper While washing the venturi tube and then feeding it to the water pulper, the paper edge conveyed at this time is continuous. The disadvantage of this method is that when the speed of the winder is relatively high, the power of the selected fan is large, which will increase the operation. Cost, increase loss.

Label Paper Making Machine

Rewinder mechanical structure and control process ---

 

Second, the main structure of the winder

2.3 Rolling Department
1. Stretching device
The stretching device of the rewinder is set to keep the paper web slit after slitting. In some paper cutting knives, the stretcher is also used. The main function is to eliminate the texture and slack of the paper web. Mainly, it can maintain the good operation of slitting. There are three types of stretchers that we often use today: D-shaped stretches, curved rollers, and Z-type double-bar stretchers.
2, support roller
The backup roll is mainly used to support the paper roll, which is composed of a controlled cast iron roll or a general tube roll. The roller body is mainly cast iron pipe and steel pipe, and its diameter is usually 400-700 mm or more according to the width of the winder. The center-to-center ratio between the rolls of the backup roll should be greater than the roll diameter. Only at such a distance, the roll core does not get caught in the middle of the roll when the support roll begins to curl.
When the winder is running at high speed, in order to avoid vibration during high-speed operation, the design of the backup roller must be minimal when supporting the paper roll. The radius is a function expression of the speed and width of the winder, mainly by allowable The critical speed and the degree of winding are determined because at this time the diameter of the backup roll has less chance of producing a defect in the roll hardness than the small diameter support roll. When coiling coated paper or very thin paper, we should consider using a larger diameter backup roll. On a rewinder with a small width, we generally use a 600mm roll diameter.
 

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com