Pos Paper Roll Machine

Pos Paper Roll Machine

Maintenance of the winder
1. The transmission of the toilet paper rewinder, such as the gear chain, needs to be added with butter.
2. The rewinding machine generally does not have problems. The consumable parts are nothing more than small pinions. If one is added, the printing knife is easy to break. The wool roller will become thinner after one and a half years of loading, and it needs to be transported back to the factory for renovation. If the embossing pattern needs to be replaced in the steel roll embossing device, it is necessary to transport the steel roll back to the original factory for modification, and it will not cost much.
3. Pay attention to the voltage of the winder should be stable, otherwise it is easy to burn the motor; pay attention to hygiene, do not let the debris fall between the steel roller and the roller.

Pos Paper Roll Machine

Guolian Small Winder Introduction---

First, the function: a variety of tape defective products re-rolled
Second, the characteristics:
A. The take-up shaft is driven by a DC 1HP motor and can be steplessly changed.
B. Automatic counting, convenient for setting the length of the winding.
C. The rewinding tension is adjusted by the spring, and the tension adjustment is convenient.
D. The structure of the machine is light and compact, and it is a desktop device, which is convenient to move.

Third, the specifications
1. Roller surface width: 105mm
2. Maximum discharge diameter: standard is 150mm and length is 400mm
3. Take-up diameter: Ø76mm-300mm
4. Rewind width: 12mm-100mm lengthening type is 300mm
5. Take the paper heart: paper tube 3”
6. Mechanical speed: 0~150M/min per minute

Fourth, the host configuration
1. Discharge shaft: 3" movable type (1)
2. Dispensing rack: lengthened 300mm diameter (1)
3. Main motor: DC motor 1HP (1 set)
4. Take-up tension: Spring control (1 set)
5. Length control: four-digit electronic counter (1 group)
6. Take-up shaft: 3" tube core (1 group)

Pos Paper Roll Machine

Automatic rewinding machine speed ratio adjustment method ---


        The rewinding machine is the first station of the production line equipment of the welcoming machine. The good running condition of the rewinding machine directly affects the quality and production efficiency of the post-processing welcoming paper. The rewinding machine should be able to operate normally and in a good production state. In addition to the good and non-damage of the components, the reasonable adjustment and control of the transmission ratio of the whole machine is very important.
        When the rewinding machine is produced, the original paper web is conveyed by five transmission rollers and belts, that is, a paper feeding belt, a curved roller, a rear platen roller, a front platen roller, a winding roller, and the like. Each of the base papers is thin, the elongation is limited, and the transmission speed ratio is unstable, and the paper web is easy to wrinkle and be broken during the continuous acceleration and deceleration operation of the winder. Reasonable adjustment and control of the speed of each drive roller and paper feed belt can greatly reduce the phenomenon that the paper web is broken. After many daily adjustments, the author summarizes the following key adjustment methods. 1. Stable paper feed belt conveys the line speed of the original paper web. The paper feeding belt of the rewinding machine is driven by the V-belt through the stepless speed-regulating wheel. When the output torque is large, the driving V-belt is close to the outer edge of the speed-regulating wheel, and the transmission speed will be more stable. In order to achieve such a stable transmission effect, the speed ratio of the main gearbox can be adjusted step by step to make the speed of the winding roller slower, and at the same time adjust the speed control handwheels of the paper feed belt of the original paper frame, so that the three sets of transmission triangle belts are in The outer edge of the stepless speed regulation wheel is in a reasonable position until the winding speed of the winding roller and the paper feeding belt are the same.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com