Plastic Film Packaging Machine

Plastic Film Packaging Machine

Maintenance of the winder
1. The transmission of the toilet paper rewinder, such as the gear chain, needs to be added with butter.
2. The rewinding machine generally does not have problems. The consumable parts are nothing more than small pinions. If one is added, the printing knife is easy to break. The wool roller will become thinner after one and a half years of loading, and it needs to be transported back to the factory for renovation. If the embossing pattern needs to be replaced in the steel roll embossing device, it is necessary to transport the steel roll back to the original factory for modification, and it will not cost much.
3. Pay attention to the voltage of the winder should be stable, otherwise it is easy to burn the motor; pay attention to hygiene, do not let the debris fall between the steel roller and the roller.

Plastic Film Packaging Machine

Belt rewinding machine design and working principle ---

1 belt roller device
Structure
The belt and stick set consists of two belt rollers with intermediate and end supports! A rubber support belt surrounds the belt roller. The inner surface of the support belt has a guiding profile that controls the operation of the belt. There is also a correspondingly concave surface on the belt roller. The belt roller has been joined together by a rocker and a hydraulic cylinder from below. The belt tension can be adjusted with a hydraulic cylinder during the winding process.
The motor drives the rear belt roller to run, and the other roller is carried by the belt. The belt roller is equipped with a hydraulic brake system. The belt roller bearing housing is lubricated with lubricating oil. The oil flow and temperature of the lubricating oil system are detected by the sensor. There is a directional blow tube between the two rolls to ensure that no space remains in the space between the two rolls. The lifting device has been installed under the belt. The lifting device is used for changing rolls. The lifting device comprises a hydraulic cylinder and a lifting plate interlocked with the rear bottom roller during the lifting process.
Belt roller unit:
1- bottom roller
2- rear belt roller
3- front belt roller
4- belt
5-belt telescopic hydraulic cylinder

Principle of operation
The core is placed between the back bottom roll and the back belt roll. The paper core is supported at that position throughout the initial crimping process up to a diameter of approximately 500 mm (17.9 in). The over 500 mm (17.9 in) belt begins to support the increasing area of ??the paper roll, and the weight of the roll is reached when the paper roll is particularly large. Mainly supported by a belt.

Plastic Film Packaging Machine

Belt rewinding machine design and working principle ---

rear bottom roller

The movable beam is fixed to the frame. The movement of the platen roller beam moves with the hydraulic cylinder attached to the beam. The platen roller is decoupled from the hydraulic cylinder during the rewinding process. The platen roller also includes a pressure sensor to measure the pressure between the platen roller and the frame.
The platen roller has a position measuring device for providing a position about the platen roller and the diameter of the paper roll. Based on the above information, the hydraulic cylinder moves in accordance with the separation design curve as the diameter of the paper roll continues to increase. The hydraulic cylinder is equipped with a hydraulic hose rupture protection valve to prevent the paper roll from suddenly falling when the hose is damaged.
working principle 
The platen roller provides additional load to the paper roll at the beginning of the rewinding. At a later stage of the rewind, the pressure is released. In the final stage, the platen roller ensures that the paper roll is in place.
During the threading and changing process, the platen roller is raised to the rear of the safety lock at the top position. The safety lock prevents the platen roller from suddenly falling when the device malfunctions. The platen roller is automatically decompressed when the platen roller is lowered to the core or the base. If the lowering control is terminated before decompression, the platen roller will be activated and the platen roller will be raised to the upper position.
During the rewinding process, the contact surface between the platen roller and the paper core must be carefully observed. If the platen roller is very close to the core, special care must be taken during the rewinding process. If the core starts to vibrate, the speed must be lowered immediately. There is a vibration indicator on the pressing roller beam to facilitate speed reduction in that case.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com