Tape Jumbo Roll Slitter And Rewinder Machine

Tape Jumbo Roll Slitter And Rewinder Machine

Maintenance of the winder
1. The transmission of the toilet paper rewinder, such as the gear chain, needs to be added with butter.
2. The rewinding machine generally does not have problems. The consumable parts are nothing more than small pinions. If one is added, the printing knife is easy to break. The wool roller will become thinner after one and a half years of loading, and it needs to be transported back to the factory for renovation. If the embossing pattern needs to be replaced in the steel roll embossing device, it is necessary to transport the steel roll back to the original factory for modification, and it will not cost much.
3. Pay attention to the voltage of the winder should be stable, otherwise it is easy to burn the motor; pay attention to hygiene, do not let the debris fall between the steel roller and the roller.

Tape Jumbo Roll Slitter And Rewinder Machine

Belt rewinding machine design and working principle ---

 

9 small paper rolls launched
The small paper roll ejecting device is used for those paper rolls that are too small for the paper feed roller. The small paper roll ejecting device is mounted on the paper feed roller. It relies on hydraulic pressure to move. The minimum diameter that the small paper roll exit can be pushed out is 200 mm (7.9 in).


10 paper cutter construction
The paper cutter is a zigzag blade, which cuts the slit webs during roll ejection. The paper cutter rises from the paper roll to the paper cutting position. The movement of the paper cutter is done by a lever driven by a hydraulic cylinder.
working principle 
The paper roll is pressed against the raised paper cutting blade by the ejector pin and cut.


11 core positioning pin
The end of the core loader is a paper core locating pin attached to the rewinder frame. The paper core positioning pin includes a metal plate and a frame. The scale on the core locating pin shows the position of the locating pin. The paper core locating pin holds the paper core in the correct position on the core loader only by the edge of the slitter. The core positioning pin is placed in close proximity to the slit and is locked in that position by the locking arm.
 

Tape Jumbo Roll Slitter And Rewinder Machine

Belt rewinding machine design and working principle ---

16
Stretching device after cutting the web
The purpose of stretching after slitting is to stretch the sheet in the lateral direction and to separate the cut sheets from each other.
Construction
After the cut, the stretch is achieved by the wrap angle roll. The wrap angle roll includes a stretch roll. The first spreader roll is above the cut sheet and the second spreader roll is below the sheet. Both rollers are mounted on a frame that is used to adjust the stretch.
The spreader rolls above the sheet have good curvature. The spreader roll is equipped with a bend control device. The hand wheel and screw mechanism are used on the maintenance side to control the direction and tendency of the bend.
The segmented spreader rolls are under the sheet of paper. The segmented stretch roll is placed over an arcuate roll mounted on a steel beam. The cylinder is mounted below the segmented spreader roll. The bending curvature of the spreader roll can be modified by adjusting the gas pressure to adjust the cylinder.
Stretching principle:
When the sheet passes under the first roller, the sheet is guided from the center to the outside by a curved roller at each slightly different angle. At this time, there is a small gap between the cut sheets. When the sheet is placed over the second roll, the sheet encounters an arc of the opposite direction, which allows the sheet to remain parallel through the gap.
The stretching effect is mainly controlled by changing the wrap angle of the spreader roll. In addition, the stretching effect can also be controlled by changing the bow position of the stretch roll to control and change the arcuate curvature of the segmented spreader roll. The spreader roller is driven by a separate drive motor through a V-belt. The speed of the stretching roller is the same as the speed of the rewinding machine.
Measuring the exit roller diameter 1- Diameter measuring sensor 2- Support frame 3- Reel
 

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com