High-Speed Slitting Machine For Scotch Tape

High-Speed Slitting Machine For Scotch Tape

Rewinding Machine operating procedures -  Job preparation.
1. The operator arrived at the post 10 minutes in advance.
2. Check and understand the operation of the equipment, check equipment hazards, check equipment hygiene and on-site hygiene, and make a good inspection record.
3. Understand the production situation and quality of the class before the class, familiar with the work site.
4. Familiar with process standards, master product quality requirements, variety specifications, dimensions, roll length, indicators and tasks.
5. Do personal safety protection and equipment safety protection.
6. Carefully implement the handover system and make a record of the handover.

High-Speed Slitting Machine For Scotch Tape

Rewinding Machine operation safety regulations - 

Second, the operation steps:

7. When the layers of paper are completely flat and enter the rewinding, the waste coils are taken out to the normal production state. 8, check the production situation:
(1) Check whether the two ends of the base paper are symmetrical. For example, the auger can adjust the auger on the unloading frame to the ends of the paper. (2) Check whether the punched paper is clear, the punching is not clear or the missing teeth are checked. Whether the knife is broken or not
Whether the wire is loose, adjust the height of the bottom knife, and mass production after inspection;
(3) Check whether the paper feeding tension of the rewinding paper is consistent, keep the paper surface flat and no wrinkles, such as inconsistency
Then adjust the paper return belt hand wheel on the paper exit frame;
(4) Check whether the paper between the embossing stick and the winding area is flat and tight, if it meets the requirements, if it does not meet the requirements,
Then adjust the gearbox handwheel (when adjusting the gearbox handwheel, you can't stop the adjustment, you need to turn it on slowly); (5) Check whether the semi-finished paper roll is tight, the diameter and weight meet the product standard requirements, and the two ends are neat (straight
The deviation of the diameter shall not exceed ±1mm, and the weight deviation shall be within ±2);
(6) Whether the width of the glue seal of the paper ball meets the standard (package standard is 10mm-15mm), the penetration of glue
No more than 3 single-layer papers;
(7) Do not arbitrarily tamper with the inverter, programmed wiring and settings in the electric box; (8) Non-operator operators must not let the machine operate without the consent of the supervisor;

Third,. After the above steps are checked normally, Slowly speed up to normal operation.

High-Speed Slitting Machine For Scotch Tape

Four release and one rewinding machine operation program ---

First, prepare for inspection before starting the machine
1. Dust removal: Before cleaning, ensure that the work area is cleaned and there is no dust. There is no dust on the shaft. Clean it once with an air gun to remove the dust.
2, the direction of receiving and discharging: When unwinding the bar, pay attention to the direction of feeding. The discharge stick is counterclockwise. The receiving stick is clockwise.
3. The position of the gear and the position of the barrel are placed: the gear of the discharging stick and the receiving stick should be in the middle of the gear of the motor, avoiding the friction between the gear and the gear around the gear during the fine adjustment, thus causing damage to the gear or the motor; The receiving barrel should be the same on the scale of the stick.
4. Inflatable locking: After the position of the barrel is placed, use a high-pressure air gun to ventilate each barrel to ensure that each barrel is locked. (It is strictly forbidden to start the machine without inflation)
5. Induction: Manually pass the materials through the intermediate rollers and the tension sensor in sequence, and finally wrap the receiving core and fix the material head by hand. Note: Ensure that the material is neat and flat during the process of fixing the material. Put the material well and press the pressure shaft on the receiving roller.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com