Vinyl Cutting Roll Machine

Vinyl Cutting Roll Machine

Rewinding Machine operating procedures -  Job preparation.
1. The operator arrived at the post 10 minutes in advance.
2. Check and understand the operation of the equipment, check equipment hazards, check equipment hygiene and on-site hygiene, and make a good inspection record.
3. Understand the production situation and quality of the class before the class, familiar with the work site.
4. Familiar with process standards, master product quality requirements, variety specifications, dimensions, roll length, indicators and tasks.
5. Do personal safety protection and equipment safety protection.
6. Carefully implement the handover system and make a record of the handover.

Vinyl Cutting Roll Machine

Design and application of constant tension and load distribution control for winder---

2Rewinder control research status at home and abroad
Rewinding machine is an important papermaking machine. It is usually installed behind the paper machine. Its speed should be 2-3 times of the speed of the paper machine, generally 1500-1800m/min, up to 300om/min. When threading, run at a maximum speed of 1:100. In order to ensure continuous paper and loose paper during the rewinding process, the tension of the paper web must be kept constant; in order to ensure the tight and loose quality inside the finished paper, the load distribution of the front and rear bottom roller motors must be performed. Therefore, the main performance requirements of the rewinder for the electric drive system are long-term linear speed, adjustable speed and wide speed range, and fast response.
The control of the early rewinder is mainly based on DC drive, and the DC control system is composed of discrete components or analog regulators to realize the above control functions. Since the transmission of analog signals requires a one-to-one physical connection, the signal changes slowly, which increases the overhead of computer speed and accuracy, and the anti-interference ability of signal transmission is poor, and paper breakage and wrinkling often occur in the production process. So in the mid-to-late 1980s, the analog regulator was replaced by a digital regulator, and the DC digital control system of the winder appeared. This control system is more stable, reliable and suitable for maintenance than the analog system, and is more suitable for interface with the factory computer. In the mid-1990s, most of the newly-invested rewinders in the domestic paper industry used all-digital DC-speed converters produced abroad, and the more famous ones were the 6RA7O series from Siemens and the 590 series DC-speed converters from Continental Transmission.
Due to the DC motor commutator and the brush, under the stable conditions, the design speed of the winder can only reach 1800m/mni, and the accuracy of the digital regulator is still limited to about 0.08% of the maximum speed, which can not meet the high speed paper. The matching requirements of the machine (the speed of the winder should be 2-3 times the speed of the paper machine). In the early 1980s, European and Japanese developed AC variable frequency speed control devices. This technology was successfully introduced to the United States in the mid-1980s and used in rewinders. The biggest advantage of the AC drive is that the AC motor is simple in construction and reliable in operation, and it requires much less maintenance and repair than DC motors.
 

Vinyl Cutting Roll Machine

Design and application of constant tension and load distribution control for winder---

4.1 Research significance
The significance of this paper is to apply advanced field bus and frequency conversion technology to the traditional paper industry, making the rewinder control system very practical and advanced for a long time.
Firstly, the new Profibus field bus is used to replace the system's large number of I/O wiring, which effectively avoids the interference of the signal; the OP operation panel is used to replace the analog secondary instrument and switch button of the original system. The control system is divided into two levels: the monitoring machine (operator panel) and the field control level (lower position machine). Through the system, the operator can timely understand the various operating states of the winder through the OP panel, analyze the cause of the fault, and make corresponding adjustments and controls on the OP panel according to the site conditions in time. The new control system adopts the frequency conversion control technology, which abandons the DC rotation control mode of the original system of the winder. The application of the frequency conversion technology improves the speed and control precision of the system. The modified vehicle speed reaches 1200m/min (line speed), which is the original system. Twice, at the highest speed, the speed error does not exceed 2%. The friendly man-machine interface system can effectively control the entire production process of the winder, realize effective control of key production parameters, ensure safe and stable production, improve economic efficiency, and reduce labor intensity of workers.
Secondly, the implementation scheme of the new control system has strong universality. The software and hardware design and transformation of the general data acquisition system can connect the original system to the field bus, and the design of the tension and load distribution control of the winder The equipment transformation in the paper industry and the cigarette industry has certain reference significance.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com