Double-Shaft Film Slitter

Double-Shaft Film Slitter

Rewinding Machine operating procedures - Preparation for rewinding.
1. The crane operator and the rewinding personnel first check whether the information on the parent roll tracking slip on the base paper meets the requirements of the technical standards, specifications and specifications.
2. Check whether the labels of various paper diseases on both ends of the base paper roller are clear and consistent with the contents on the tracking sheet.
3. The crane operator should operate carefully according to the safe operation rules of the driving.
4. Place the base paper roll on the unloading frame smoothly, place the drum groove on the shaft head, place the track groove in the locked position, and connect it with the hydraulic coupling.
5. Jog the left and right shift buttons of the exit tray to bring the ends of the web to a position that can be trimmed (to be threaded).
6. The operator should make a detailed record of the paper (such as shift, shift, production date, roll time and paper roll code, etc.).

Double-Shaft Film Slitter

Rewinding Machine operation safety regulations - 

Second, the operation steps:

7. When the layers of paper are completely flat and enter the rewinding, the waste coils are taken out to the normal production state. 8, check the production situation:
(1) Check whether the two ends of the base paper are symmetrical. For example, the auger can adjust the auger on the unloading frame to the ends of the paper. (2) Check whether the punched paper is clear, the punching is not clear or the missing teeth are checked. Whether the knife is broken or not
Whether the wire is loose, adjust the height of the bottom knife, and mass production after inspection;
(3) Check whether the paper feeding tension of the rewinding paper is consistent, keep the paper surface flat and no wrinkles, such as inconsistency
Then adjust the paper return belt hand wheel on the paper exit frame;
(4) Check whether the paper between the embossing stick and the winding area is flat and tight, if it meets the requirements, if it does not meet the requirements,
Then adjust the gearbox handwheel (when adjusting the gearbox handwheel, you can't stop the adjustment, you need to turn it on slowly); (5) Check whether the semi-finished paper roll is tight, the diameter and weight meet the product standard requirements, and the two ends are neat (straight
The deviation of the diameter shall not exceed ±1mm, and the weight deviation shall be within ±2);
(6) Whether the width of the glue seal of the paper ball meets the standard (package standard is 10mm-15mm), the penetration of glue
No more than 3 single-layer papers;
(7) Do not arbitrarily tamper with the inverter, programmed wiring and settings in the electric box; (8) Non-operator operators must not let the machine operate without the consent of the supervisor;

Third,. After the above steps are checked normally, Slowly speed up to normal operation.

Double-Shaft Film Slitter

Four release and one rewinding machine operation program ---

6. Check if the power indicator on the outside of the tension control cabinet is lit.
7. In the touch screen, you need to input or rewrite the following parameters:
1 counting length is cleared (if it is necessary to re-measure the length);
2 automatic acceleration speed (refers to the speed we reach after the automatic acceleration of the machine after pressing the acceleration button delay)
3 Automatic acceleration time (refers to the time required for the machine to automatically accelerate from zero speed to the design of the highest machine speed. The shorter the time setting, the faster the acceleration.)
8. Tension control: Set the tension of each discharge motor in the touch screen. The discharge motor mainly provides a reverse torque, generates tension on the paper surface, keeps the paper web flat, and the speed control of the discharge motor is a process of gradually increasing speed, but the line speed remains unchanged.
9. Each console has its own power switch, which can be switched on and off as needed.
10. The forward and reverse running buttons are set on the console, and the user can select the running direction according to the needs.
 

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com