Jumbo Roll Film Slitting Machine

Jumbo Roll Film Slitting Machine

Rewinding Machine operating procedures - Preparation for rewinding.
1. The crane operator and the rewinding personnel first check whether the information on the parent roll tracking slip on the base paper meets the requirements of the technical standards, specifications and specifications.
2. Check whether the labels of various paper diseases on both ends of the base paper roller are clear and consistent with the contents on the tracking sheet.
3. The crane operator should operate carefully according to the safe operation rules of the driving.
4. Place the base paper roll on the unloading frame smoothly, place the drum groove on the shaft head, place the track groove in the locked position, and connect it with the hydraulic coupling.
5. Jog the left and right shift buttons of the exit tray to bring the ends of the web to a position that can be trimmed (to be threaded).
6. The operator should make a detailed record of the paper (such as shift, shift, production date, roll time and paper roll code, etc.).

Jumbo Roll Film Slitting Machine

Rewinder mechanical structure and control process ---

As the last process in the papermaking industry, the winder is the fastest running machinery in papermaking machinery. Its speed can reach 1500~1800m/min or even the speed can reach 3000m/min or more. The winder is in the papermaking industry. The important role that can not be ignored, the paper roll from the paper machine must be rewinded by the winder to get the finished paper roll we need, and the quality of the finished paper roll is not only determined by the paper machine, The role of the winder is also of particular importance.

 

The working principle of the winder is to install the large paper roll produced from the paper machine on the paper exit frame of the winder. In order to maintain a certain tension of the paper web, the brake device must be installed on the paper return frame. A brake motor is installed on the paper exit frame. If the paper breaks during the rewinding process, the brake device can also brake quickly to reduce paper loss. The web is cut to the width we need by the slitting roller, the paper guide roller and the winder slitting mechanism, and then re-rolled into a paper roll according to the required tightness and the diameter of the finished paper roll. The main structural parameters of the winder are the width of the paper roll that can be rewinded, the maximum speed that the rewinding machine can reach, the quality of the finished paper roll, the maximum diameter of the ejecting roll and the roll paper, and the method of cutting the paper.

 

There are many types of rewinders, and other devices can be equipped in the rewinder as needed to become a joint machine. The rewinder can basically be divided into the following five types: upper paper rewinder, lower paper rewinder, single roll rewinder, special rewinder and thin paper rewinder. Since the research object of this subject is mainly for the lower threading rewinding machine, the introduction and explanation of the double bottom roller lowering paper rewinding machine will be given.

Jumbo Roll Film Slitting Machine

Rewinder mechanical structure and control process ---

 

Second, the main structure of the winder

2.2 Longitudinal section
In the mechanical system of the winder, the slitting mechanism is a very important part of the winder. In order to ensure a straight and smooth cutting edge, the quality control of the finished paper roll plays an important role in ensuring the volume. It is easy and can reduce the fluffing during printing. The slitting mechanism should be installed as close as possible to the paper roll so that it can produce a lateral movement more than necessary during the process of cutting the web without curling.
The high-speed rewinding paper conveying system is also very important in the application. The old-fashioned rewinding machine is mainly handled by manual. With the increase of the speed of the rewinding machine, the manual can no longer be processed. There are two ways to transport the paper side of the reel: fan direct pumping and venturi suction. The direct drawing type of the fan mainly uses a centrifugal fan, and the fan is placed under the floor. The inlet of the fan and the air duct near the longitudinal cutting edge are connected to each other, and the blade of the fan is also equipped with a wind blade. When the fan is sucked, it will be broken by the blade and then sent to the water pulper. However, since the edge of the paper has to pass through the inside of the fan, the blade transported by this type of paper is very worn and needs to be changed frequently. Venturi suction is also used in the high-pressure centrifugal fan, but the paper edge does not pass through the fan, directly the longitudinal cutting edge of the duct into the venturi pipe, the wind machine generates negative pressure in the venturi, and then the paper While washing the venturi tube and then feeding it to the water pulper, the paper edge conveyed at this time is continuous. The disadvantage of this method is that when the speed of the winder is relatively high, the power of the selected fan is large, which will increase the operation. Cost, increase loss.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com