Auto Film Sitting Procution Line

Auto Film Sitting Procution Line

Rewinding Machine operating procedures - Preparation for rewinding.
1. The crane operator and the rewinding personnel first check whether the information on the parent roll tracking slip on the base paper meets the requirements of the technical standards, specifications and specifications.
2. Check whether the labels of various paper diseases on both ends of the base paper roller are clear and consistent with the contents on the tracking sheet.
3. The crane operator should operate carefully according to the safe operation rules of the driving.
4. Place the base paper roll on the unloading frame smoothly, place the drum groove on the shaft head, place the track groove in the locked position, and connect it with the hydraulic coupling.
5. Jog the left and right shift buttons of the exit tray to bring the ends of the web to a position that can be trimmed (to be threaded).
6. The operator should make a detailed record of the paper (such as shift, shift, production date, roll time and paper roll code, etc.).

Auto Film Sitting Procution Line

Belt rewinding machine design and working principle ---

2 rear bottom roller
The roller is covered with a steel shell. It maintains a dynamic balance at a speed equivalent to the design speed. The roller has a coating and a spiral groove. Equipped with hydraulic brake system. The roll outer coating is used to attempt to increase the friction between the roll surface and the paper during rewinding. Air is discharged along the spiral groove between the roll surface and the paper roll.
Vacuum drum
The rear bottom roller has a hole. Vacuum suction is generated by a blower. This facilitates paper machine threading to ensure that the cut sheet fits snugly against the roll during roll change.
(traction) platen roller device:
1-cylinder safety valve
2- Pressing roller
3- Press roller safety lock
4- Photocell
5- Pressing roller beam
6- Paper roll
The platen roller is used to hold the paper roll during the roll paper process. The pressure between the roller and the drum is adjusted by adjusting the pressure of the platen roller. The rewinding pressure affects the roll density and sheet tightness and winding force. In addition, the platen roller ensures that the paper roll is in an adapted position.
Construction

Auto Film Sitting Procution Line

Belt rewinding machine design and working principle ---

3. Platen roller power:
A motor that drives the platen roller by a timing belt drive is mounted on the platen roller beam. The coupling between the individual bearings of the platen roller ensures that the speed of each combined reel is the same. The speed of each part of the platen roller is the same during operation.
Platen roller photocell:
There is a photocell at the end of the platen roller beam. If the paper or any other obstacle enters the photocell illumination area, the photocell signal will immediately stop the downward movement of the platen roller. During operation, the photocell's monitoring paper does not wrap around the platen roller. If something happens, the photoelectric signal activates the alarm to stop the rewind.
Core device:
1-trache
2- top core head
3- drive motor
4- positioning stop pin
5- Safety lock in the top core lock
The core between the drums is locked before the rewinding process begins. Keep the paper roll in place during the running of the paper core locking process.
Construction
The core lock device includes a paper core plug, a cone, and a sleeve. The core of the paper core is fixed in a core seat that can be vertically up and down and can reduce friction. The core of the paper core is supported by the upper bearing of the cone, so it rotates freely. The locking of the core and the upward movement of the core locking device are done hydraulically. The vertically moving hydraulic cylinder supports the weight of the core collet so that the home can rise as the diameter of the paper roll increases. The change in the slit width is adjusted with the help of the hydraulic transfer knob. The paper core collet has a relatively low position on the locating pin. As the paper core model changes, the latch and the paper roll chuck must change. The core collet structure has a shock absorber that is lowered onto the positioning stop pin at the core of the paper core. The safety lock has a compressed air cylinder open.
working principle 
Before the rewinding begins, the collet is knocked into the paper core. The locking cylinder of the operating side core collet has a locking pressure that is less than the drive side. If the core is too long, the operating side cylinder will retract. As the size of the paper roll continues to increase, the paper core collet moves with the paper roll, preventing the paper roll from moving laterally.
Before the paper roll is pushed away from the winder, the paper core chuck is unlocked and moved to the upper position. The appropriateness of the width of the paper core collet is related to the cutter positioning device. The sensor mounted in the paper core chuck records the pulse as the spool rotates. These pulse signals are not used to calculate the paper roll diameter. There is a sensor in each side of the cone. If one side of the sensor is damaged, the other side can be used immediately.
 

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com