Tape Production

Tape Production

Rewinding Machine operating procedures - Unwinding paper core
(1.) Post operator
1. First check the cutting distance of the measuring cutter, which is consistent with the specifications required by the process standard.
2. Before placing the paper core, first check whether the paper core used meets the requirements for use:
A. Is the size of the specification the same as the roll paper size?
B. Is the inner diameter and outer diameter of the paper core acceptable (the thickness is consistent).
C. Does the strength of the paper core meet the requirements?
D. Whether the port is layered or burred.
E. Can be put on the machine after passing the inspection and passing the test.
3. Signal the main operation: Start the ejector pin pump button and insert the paper core onto the ejector cone.
4. Shake the two thimble handles to the left to push the core.
5. Align the edge of the paper core port (the difference between left and right cannot exceed one millimeter).

(2) Main operation
1. Review again whether the paper cores on the board meet the requirements.
2. Review whether the thimble is inserted into the lock (avoid the end of the paper roll is not aligned)
3. Check the sharpness of the upper and lower round knives, the depth of the occlusion and the angle to ensure the quality of the trimming.

Tape Production

Four release and one rewinding machine operation program ---

Fifth, sorting out
1. After the work is finished, turn off the power and put the main power switch down.
2. Clean up the work area.

Maintenance matters:
1. It is necessary to add oil to the bearings.
2. Use a manual grease gun to add butter to the bearing of the belt shaft once every six months; when the gear is missing butter, pay attention to add butter.

Precautions: 
1. The winder has certain dangers, so it is necessary to pay attention to safety during operation.
2. Never touch the ultrasonic probe on the pressure roller.

Tape Production

Rewinder mechanical structure and control process ---

 

I. Overview of the double-roller under the paper rewinding machine
The mechanical structure of the lower paper rewinding machine is shown in Figure 2-1. It can be seen from the mechanical structure diagram of the rewinding machine that the lower paper rewinding machine is fed into the paper web from below the rewinding machine. The paper web is wound around a support roll and then rolled up with a roll of paper. The paper is ejected from the unwinding roll, passed through the lower transfer roll, and then the web passes through the slitting mechanism at a fixed position, bypassing the front backup roll (press The second roller in the direction of the paper line or the back support roller is then wound on the take-up reel.
During the rewinding process, the paper web passes through the eject roller, and the tension force formed by the paper web pulls the paper roll toward the support roller, and the tension of the paper roll is stabilized by the action of the tension, and the rewinding machine can be made at a high speed roll. The quality of the paper roll can be guaranteed when taken. The lower thread rewinding machine can also control the pressure between the platen roller and the paper roll by changing the transmission torque difference of the two supporting rollers, so that the pressure of the finished paper roll can be controlled, and the quality of the paper roll can be Do a good job of control.
It can be seen from the figure that since the slitting mechanism of the lower threader rewinding machine is installed at a fixed position, this can avoid axial sway during the rewinding process, and also facilitates the control of the winding of the paper roll. The role of most of these rewinders in the Middle East is not very high, very close to the ground, the center of gravity, relatively low, due to the lower center of gravity, the rewinder can remain stable at high speeds, so this Types of rewinding machines are widely used, and most of the paper mills in China use the lower thread rewinding machine. Through many practices, this rewinding machine is also the best performance. And its speed can reach 2,500 meters per minute, the width is also long, can reach 10 meters, can handle the rewinding of different types of paper, from low basis to cardboard can be re-rolled. Of course, it also has its own shortcomings. The disadvantage is that because it is close to the ground, it is not easy for the operator to access the bottom of the machine. It is also difficult to guide the paper. Therefore, when the mechanical equipment is installed, a pit will be placed under the machine. In order to make the operator more accessible, the high-grade rewinding adopts the automatic threading structure, and there is no such problem.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com