Slitting Bopp Machine

Slitting Bopp Machine

Rewinding Machine operating procedures - Unwinding paper core
(1.) Post operator
1. First check the cutting distance of the measuring cutter, which is consistent with the specifications required by the process standard.
2. Before placing the paper core, first check whether the paper core used meets the requirements for use:
A. Is the size of the specification the same as the roll paper size?
B. Is the inner diameter and outer diameter of the paper core acceptable (the thickness is consistent).
C. Does the strength of the paper core meet the requirements?
D. Whether the port is layered or burred.
E. Can be put on the machine after passing the inspection and passing the test.
3. Signal the main operation: Start the ejector pin pump button and insert the paper core onto the ejector cone.
4. Shake the two thimble handles to the left to push the core.
5. Align the edge of the paper core port (the difference between left and right cannot exceed one millimeter).

(2) Main operation
1. Review again whether the paper cores on the board meet the requirements.
2. Review whether the thimble is inserted into the lock (avoid the end of the paper roll is not aligned)
3. Check the sharpness of the upper and lower round knives, the depth of the occlusion and the angle to ensure the quality of the trimming.

Slitting Bopp Machine

Rewinder mechanical structure and control process ---

 

Second, the main structure of the winder

2.4 Pressure mechanism
1, the platen roller
First, in the rewinder system, the platen roller has a significant impact on the tightness control of the paper roll. Among them, the pressure adjusting mechanism plays a role of keeping the pressure of the paper roll and the supporting roll nip constant, and the main purpose is to prevent the paper roll from slipping or being wound too tight at the beginning of the work. The paper roll slips because the paper roll is too light, and the winding is too tight because the pressure is too high until the rewinding to the later stage. In the modern rewinder system, the platen roller is automatically controlled, so that the paper can be additionally applied. The force.
2. Hydraulic (air pressure) suspension mechanism
Under normal circumstances, the adjustable pressure actuators use hydraulic suspension scale mechanism. We install a potentiometer attached to the platen roller to display the diameter of the finished paper roll, which is sent through the potentiometer. The signal is transmitted to the pressure program control unit to calculate the pressure, so that the oil pressure in the suspension scale can be changed, thereby achieving pressure control of the platen roller.

Slitting Bopp Machine

Guolian High Speed ??Slitting Rewinder Technical Description ---

The specific technical structure is described as follows:

2. Paper cutting department:
It is mainly composed of independent frame, guiding paper-feeding roller, segmented and extended arc roller device, front and rear segment guide roller, bottom knife device, round knife device and paper suction fan.
The frame is welded by steel plates and is heavy and sturdy, completely independent of the take-up frame, avoiding the effects of possible vibration on the paper cut.
Guided paper roller, diameter Φ700mm, material Q235, directly driven by motor, chrome-plated surface, hydraulic disc brake and vertical adjustment device, can be adjusted along the scale with worm gear system to adjust the tension of the paper web, adjustment range It is ±25mm. The large diameter guide rollers also facilitate smooth and high speed operation of the equipment and paper web. The bottom knife device, the round knife device and the front and rear segment guide rollers form a paper cutting platform to ensure that the width direction of the paper cutting is even and even. There are 6 sets of cutters, top knife φ180mm, bottom knife φ200mm, each bottom knife is driven by a variable frequency motor, the cutter is automatically positioned, and the cutting servo width is automatically adjusted by the control servo system. The entire slitting system assembly (including tool holders, guide rails, etc.) is imported from abroad to ensure its stability and reliability. The segment guide roller before and after the cutter has a diameter of φ198mm and a roller material Q235, which is divided into 5 sections. Each side of the cutter is equipped with SKF bearings. The surface of the roller body is grooved and the surface is chrome-plated. The circular knife device is composed of a cylinder, a sliding seat and a round knife, and is fixed on the circular beam beam guide rail. The feeding knife and the knife are controlled by the cylinder. After the starting, the two sides of the knife start to cut the paper edge, and the other round knife is given by the operator. After the command is fed, when the paper breaks, the air source of the middle circular knife is automatically cut off by the main control command and automatically raised. There is a web stabilizer plate on each side of the knife to guide the paper edge.
      Before the paper cutting table, a set of segmented stretching roller system is installed. The diameter of the stretching roller is φ198mm, the material of the roller body is Q235, and the surface is chrome-plated. The total length is 19 segments. The curvature of the multi-stage roller can be adjusted before and after the hand wheel to ensure the paper web. smooth.
      The suction paper edge device on both sides of the longitudinal cutter uses a special fan to break the paper edge, which makes the suction effect better, and is also beneficial to the next processing of the waste paper edge. Fan motor power 37KW air volume 11000m3 / h.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com