Machine To Make Plastic Rolls

Machine To Make Plastic Rolls

Rewinding Machine operating procedures - Unwinding paper core
(1.) Post operator
1. First check the cutting distance of the measuring cutter, which is consistent with the specifications required by the process standard.
2. Before placing the paper core, first check whether the paper core used meets the requirements for use:
A. Is the size of the specification the same as the roll paper size?
B. Is the inner diameter and outer diameter of the paper core acceptable (the thickness is consistent).
C. Does the strength of the paper core meet the requirements?
D. Whether the port is layered or burred.
E. Can be put on the machine after passing the inspection and passing the test.
3. Signal the main operation: Start the ejector pin pump button and insert the paper core onto the ejector cone.
4. Shake the two thimble handles to the left to push the core.
5. Align the edge of the paper core port (the difference between left and right cannot exceed one millimeter).

(2) Main operation
1. Review again whether the paper cores on the board meet the requirements.
2. Review whether the thimble is inserted into the lock (avoid the end of the paper roll is not aligned)
3. Check the sharpness of the upper and lower round knives, the depth of the occlusion and the angle to ensure the quality of the trimming.

Machine To Make Plastic Rolls

Guolian High Speed ??Slitting Rewinder Technical Description ---

Part II: Hydraulic and pneumatic parts:
1. Hydraulic part:
The local hydraulic system consists of a hydraulic pump station and a valve station. System control and transmission components use world famous brand products. All hydraulic lines of the winder are supplied.
The hydraulic pump station uses three oil pumps to provide pressure oil source. The hydraulic station has safety facilities such as liquid level alarm, temperature control, filter blockage alarm, and a set of circulating filtration and cooling system. The valve station control section includes:
1) Ejection shaft ejection and locking device 2) Ejection frame movement 3) Ejection shaft clutch
4) Hook protection device 5) Paper core plug locking device 6) Press roller load reducing device
7) Unloader unit 8) Push roller unit 9) Stop roller holder lifting device
10) Ejection shaft hydraulic disc brake 11) Guide roller hydraulic disc brake
12) Front and rear bottom roller hydraulic disc brakes 13) Head lifting device.
14) Paper core positioning device 15) Paper head clamping lifting device
16) Automatic paper changer lifting device
The hydraulic circuit has the following features:
A. This system adopts superimposed valve, which is simple and compact in structure, convenient in maintenance and installation, and strong in work reliability;
B. The paper return shaft, the guide roller and the two bottom rollers are equipped with hydraulic disc brakes, which assist the brake during emergency braking and share part of the braking torque. Reduce the braking load of the motor, increase reliability, and install an accumulator;

Machine To Make Plastic Rolls

Guolian High Speed ??Slitting Rewinder Technical Description ---

Second, the system configuration
1. Main transmission part: 1 set of paper-removing brake generator, 400kW (YVP4501-6 or
1LA8357-6), one roller motor (YVP225S-4), 37kW, two pressure roller motors (YVP132S-4), 5.5kW, two coiling motors (YVP355L2-4) (one for each front and rear roller) , 315kW, 6 paper cutter motor, 0.55kW, total installed capacity 1082kw (model and power are subject to final design). The rectification feedback and the inverter unit and the tension controller matched with the above constitute a transmission control system.
2. Logic control part: PLC host 1 block.
3. The logic control system selects the S7-400 series products of SIEMENS.
4. Tension control part: 1 set of tension detection and control system, using Sweden
NOBEL products.
5. 1 set of coiling roller pressure detection and control system.
6. The diameter detecting sensor of the take-up roller.
7, with position detection, pressure detection, liquid level detection, safety detection sensor and phase
The control agency should be controlled.
8. On-site operation panel, logic control panel, and electric drive panel.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com