Gummed Tape Rewinder Machine

Gummed Tape Rewinder Machine

Rewinding Machine operating procedures - Unwinding paper core
(1.) Post operator
1. First check the cutting distance of the measuring cutter, which is consistent with the specifications required by the process standard.
2. Before placing the paper core, first check whether the paper core used meets the requirements for use:
A. Is the size of the specification the same as the roll paper size?
B. Is the inner diameter and outer diameter of the paper core acceptable (the thickness is consistent).
C. Does the strength of the paper core meet the requirements?
D. Whether the port is layered or burred.
E. Can be put on the machine after passing the inspection and passing the test.
3. Signal the main operation: Start the ejector pin pump button and insert the paper core onto the ejector cone.
4. Shake the two thimble handles to the left to push the core.
5. Align the edge of the paper core port (the difference between left and right cannot exceed one millimeter).

(2) Main operation
1. Review again whether the paper cores on the board meet the requirements.
2. Review whether the thimble is inserted into the lock (avoid the end of the paper roll is not aligned)
3. Check the sharpness of the upper and lower round knives, the depth of the occlusion and the angle to ensure the quality of the trimming.

Gummed Tape Rewinder Machine

Design and application of constant tension and load distribution control for winder---

1. Rewinder structure and working principle

1.2 Working principle
The paper web is taken out from the paper take-off roller (in this paper, the lower paper feeding method is adopted), and the paper guide roller passes through the slitting mechanism, and is wound from the bottom between the front and rear bottom rollers, and then wound on the paper core. There are 1 support rollers in front of and behind the slitting mechanism, and the front and rear support rollers are equipped with tension sensors for measuring the tension of the web. The platen roller above the core ensures the hardness of the roll. Each component of the winder is driven by a separate motor. The working principle is 3: the original paper roll taken from the paper machine is placed on the unwinding roller, and the brake on the unwinding roller maintains a certain tension of the paper web, and Quickly brake the paper roll when the head is broken. The paper web passes through the guiding roller to reach the slitting device, and several slitting circular cutters divide the paper into the required width, and then send it to the take-up roller for rewinding. After reaching the specified length, the paper is stopped and replaced with a new paper core. Repeat the above process. The main structural parameters of the winder are the width of the paper that can be processed and the maximum speed, followed by the maximum diameter of the paper and roll, the method of cutting and the length.
It can be seen from the working principle of the winder that the motor of the take-up roller drives the corresponding take-up roller to rotate the paper-wound paper core, the diameter of the paper roll gradually increases, and the axial center of the paper roll increases with the diameter. Gradually moving up, the platen roller moves up and gradually reduces the pressure. The unwinding motor mainly provides a reverse torque, creating tension on the paper surface, keeping the paper web flat, and the speed control of the unwinding motor is a process of gradually increasing speed, but the linear speed of the paper web remains unchanged.

Gummed Tape Rewinder Machine

Design and application of constant tension and load distribution control for winder---

2. Main research content
(1) On the basis of understanding the working principle and production process of the rewinder, determine the AC drive configuration scheme of the rewinder and the common DC bus power supply mode.
(2) In view of the influence of the change of the winding diameter on the tension during the rewinding process and the phenomenon of paper break and loose paper during acceleration and deceleration, a composite tension control method combining direct tension and indirect tension is proposed, and the real-time calculation and dynamics of the winding diameter are designed. Torque compensation program that effectively corrects tension disturbances to ensure constant tension during rewinding
(3) Software and hardware design to complete the pressure control of the platen roller”

(4) After detailed analysis of the causes of the load distribution of the bottom roller motor before and after the detailed analysis, determine the master-slave control scheme of the two motors, design the load distribution control system.
(5) Establishing a profibus-Dp network system, designing communication between pLC and inverter! Op operation panel"

(6) Using STEP7 to design the software of the rewinder control system, using ProTool to compile the entire monitoring system screen"

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com