Sealing Tape Rewinding Machine

Sealing Tape Rewinding Machine

Rewinding Machine operating procedures - Unwinding paper core
(1.) Post operator
1. First check the cutting distance of the measuring cutter, which is consistent with the specifications required by the process standard.
2. Before placing the paper core, first check whether the paper core used meets the requirements for use:
A. Is the size of the specification the same as the roll paper size?
B. Is the inner diameter and outer diameter of the paper core acceptable (the thickness is consistent).
C. Does the strength of the paper core meet the requirements?
D. Whether the port is layered or burred.
E. Can be put on the machine after passing the inspection and passing the test.
3. Signal the main operation: Start the ejector pin pump button and insert the paper core onto the ejector cone.
4. Shake the two thimble handles to the left to push the core.
5. Align the edge of the paper core port (the difference between left and right cannot exceed one millimeter).

(2) Main operation
1. Review again whether the paper cores on the board meet the requirements.
2. Review whether the thimble is inserted into the lock (avoid the end of the paper roll is not aligned)
3. Check the sharpness of the upper and lower round knives, the depth of the occlusion and the angle to ensure the quality of the trimming.

Sealing Tape Rewinding Machine

Belt rewinding machine design and working principle ---

1 belt roller device
Structure
The belt and stick set consists of two belt rollers with intermediate and end supports! A rubber support belt surrounds the belt roller. The inner surface of the support belt has a guiding profile that controls the operation of the belt. There is also a correspondingly concave surface on the belt roller. The belt roller has been joined together by a rocker and a hydraulic cylinder from below. The belt tension can be adjusted with a hydraulic cylinder during the winding process.
The motor drives the rear belt roller to run, and the other roller is carried by the belt. The belt roller is equipped with a hydraulic brake system. The belt roller bearing housing is lubricated with lubricating oil. The oil flow and temperature of the lubricating oil system are detected by the sensor. There is a directional blow tube between the two rolls to ensure that no space remains in the space between the two rolls. The lifting device has been installed under the belt. The lifting device is used for changing rolls. The lifting device comprises a hydraulic cylinder and a lifting plate interlocked with the rear bottom roller during the lifting process.
Belt roller unit:
1- bottom roller
2- rear belt roller
3- front belt roller
4- belt
5-belt telescopic hydraulic cylinder

Principle of operation
The core is placed between the back bottom roll and the back belt roll. The paper core is supported at that position throughout the initial crimping process up to a diameter of approximately 500 mm (17.9 in). The over 500 mm (17.9 in) belt begins to support the increasing area of ??the paper roll, and the weight of the roll is reached when the paper roll is particularly large. Mainly supported by a belt.

Sealing Tape Rewinding Machine

Belt rewinding machine design and working principle ---

6 nipple guardrail
The nip guard is a sturdy mesh protector located between the belt roller and the unloader. The nipple guardrail acts as a protective device during the rewinding process. It prevents contact with rotating sticks.
Construction
The vertically moving fence is controlled by hydraulics. In the upper position, the safety lock prevents the fence from falling. When the guardrail falls, the cylinder compression safety lock opens.
working principle 
The nipple is in the upper position when the reel is stopped. When rewinding, it must fall or the winder cannot be turned on.

7 paper feed roller
The reel is moved from the roll to the unloading station by a hydraulically controlled ejector mounted on the frame.
The minimum roll diameter that the pusher roll can be pushed open but cannot be pushed open with the smallest roll is 400 mm (15.7 in)

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com