Turret Rewinding Machine

Turret Rewinding Machine

Rewinding Machine operating procedures - Start thread
1The main operator passes the inspection to confirm that the paper core and the size of the paper cut are correct.
The power-on signal informs the operator to prepare the paper. Open the paper feed roller, blower system, and paper positioning system before threading.
2. Start the rewinding machine and crawl the car at a speed of 15 meters.
3. The base paper is torn or folded into a triangle and sent to the platen roller to be delivered by the platen roller.
The paper is fed to the bottom knife roll and pressed against the horizontal roller.
4. The paper web is drawn flat and the paper trimming is aligned with the paper core and the port.
Introduce the paper edge fan to inform the main operation to stop. At this time, check the trimming situation and adjust it in time.
5. Use a piece of tape to match the paper web to the paper core, and then remove the letter immediately after sticking.
No. To inform the main operation, press the platen roller button to press the platen roller against the paper core, and start the roll paper.

Turret Rewinding Machine

Four release and one rewinding machine operation program ---

Fourth, normal shutdown and emergency stop
1. The emergency stop is faster than the normal stop speed. After the stop, the traction roller is automatically raised. The self-locking button is urgently deactivated. In the state of emergency stop, the machine cannot be started. We need to unlock the emergency stop before the machine can be started. . When the machine does not start (observe whether the start indicator is lit), we check the status of each emergency stop button.
2. When the discharge roller is about to release the material, it must be decelerated in advance. It is guaranteed that the speed of the material is just zero when it is finished.
3. Deflating Adhere the material on the receiving roller with tape, open the pressing shaft, lift the receiving roller, place it on a stable place, deflate the receiving roller, and pull out the receiving roller.

Turret Rewinding Machine

Rewinder mechanical structure and control process ---

 

Second, the main structure of the winder

2.2 Longitudinal section
In the mechanical system of the winder, the slitting mechanism is a very important part of the winder. In order to ensure a straight and smooth cutting edge, the quality control of the finished paper roll plays an important role in ensuring the volume. It is easy and can reduce the fluffing during printing. The slitting mechanism should be installed as close as possible to the paper roll so that it can produce a lateral movement more than necessary during the process of cutting the web without curling.
The high-speed rewinding paper conveying system is also very important in the application. The old-fashioned rewinding machine is mainly handled by manual. With the increase of the speed of the rewinding machine, the manual can no longer be processed. There are two ways to transport the paper side of the reel: fan direct pumping and venturi suction. The direct drawing type of the fan mainly uses a centrifugal fan, and the fan is placed under the floor. The inlet of the fan and the air duct near the longitudinal cutting edge are connected to each other, and the blade of the fan is also equipped with a wind blade. When the fan is sucked, it will be broken by the blade and then sent to the water pulper. However, since the edge of the paper has to pass through the inside of the fan, the blade transported by this type of paper is very worn and needs to be changed frequently. Venturi suction is also used in the high-pressure centrifugal fan, but the paper edge does not pass through the fan, directly the longitudinal cutting edge of the duct into the venturi pipe, the wind machine generates negative pressure in the venturi, and then the paper While washing the venturi tube and then feeding it to the water pulper, the paper edge conveyed at this time is continuous. The disadvantage of this method is that when the speed of the winder is relatively high, the power of the selected fan is large, which will increase the operation. Cost, increase loss.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com