Adhesive Tapes Double Shafts Rewinding Machine

Adhesive Tapes Double Shafts Rewinding Machine

Rewinding Machine operating procedures - Start thread
1The main operator passes the inspection to confirm that the paper core and the size of the paper cut are correct.
The power-on signal informs the operator to prepare the paper. Open the paper feed roller, blower system, and paper positioning system before threading.
2. Start the rewinding machine and crawl the car at a speed of 15 meters.
3. The base paper is torn or folded into a triangle and sent to the platen roller to be delivered by the platen roller.
The paper is fed to the bottom knife roll and pressed against the horizontal roller.
4. The paper web is drawn flat and the paper trimming is aligned with the paper core and the port.
Introduce the paper edge fan to inform the main operation to stop. At this time, check the trimming situation and adjust it in time.
5. Use a piece of tape to match the paper web to the paper core, and then remove the letter immediately after sticking.
No. To inform the main operation, press the platen roller button to press the platen roller against the paper core, and start the roll paper.

Adhesive Tapes Double Shafts Rewinding Machine

Rewinder mechanical structure and control process ---

Third, the rewinding machine control performance indicators
The rewinder is the last process in the papermaking process. The performance of the rewinder determines the quality of the finished paper roll. A complete rewinder must have the following properties:
1. Adjusting mechanism of pressure of the platen roller
As the rewinder continuously performs rewinding, the diameter of the finished paper roll is gradually increased, and the weight of the finished paper roll is also gradually increasing, so that the contact points of the finished paper roll with the front and rear bottom rolls are also changing. So you can come to a conclusion like this:
If the pressure of the platen roller is kept constant and does not change, the pressure between the contact points of the finished paper roll and the front and rear bottom rolls is not guaranteed to be constant, and the change in the contact point causes the pressure generated between them to change accordingly. Therefore, if we want the paper roll to reach the best form, we must adjust the pressure exerted by the platen roller to compensate for the influence of the above two factors. Only in this way can the pressure between the front and rear bottom rollers and the finished paper roll be guaranteed. Variety.
2, support roller torque program control In the rewinding process of the finished paper roll, in order to obtain high quality finished paper roll, the speed control or the support roller torque should meet certain conditions, if the speed control is used, the support roller The speed between the two should be less than 0.2%. As the diameter of the paper roll increases, the speed of the two supporting rollers must be close. Only in this way can the high quality finished paper roll be rewinded, but some quick checking systems cannot consider this design. 

Adhesive Tapes Double Shafts Rewinding Machine

Guolian High Speed ??Slitting Rewinder Technical Description ---

The rewinder has the characteristics of high automation, fast speed, stable operation and wide width.

First, the main technical parameters:
Paper type: high strength corrugated paper
Quantitative: 90-140g/m2
Net paper width 4950mm
Working speed 2000m/min
Design speed 2200m/min
Feed speed ≤25m/min
The maximum diameter of the eject roller φ3100mm
Roller roller maximum diameter φ1500mm
Roller roll minimum diameter φ500 mm

Maximum web tension 1500N/m Acceleration time 90s Emergency stop time 25s
Arrangement Right hand (retract the paper from the paper exit, the drive is on the right)
Dynamic balance level G1.6
Paper core 3”
Color to be determined
The rewinder is mainly composed of a mechanical part, a hydraulic and pneumatic part, an electric control part and the like.
The specific technical structure is described as follows:

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com