Adhesive Tape Jumbo Roll Rewinding Machine

Adhesive Tape Jumbo Roll Rewinding Machine

Rewinding Machine operating procedures - Start thread
1The main operator passes the inspection to confirm that the paper core and the size of the paper cut are correct.
The power-on signal informs the operator to prepare the paper. Open the paper feed roller, blower system, and paper positioning system before threading.
2. Start the rewinding machine and crawl the car at a speed of 15 meters.
3. The base paper is torn or folded into a triangle and sent to the platen roller to be delivered by the platen roller.
The paper is fed to the bottom knife roll and pressed against the horizontal roller.
4. The paper web is drawn flat and the paper trimming is aligned with the paper core and the port.
Introduce the paper edge fan to inform the main operation to stop. At this time, check the trimming situation and adjust it in time.
5. Use a piece of tape to match the paper web to the paper core, and then remove the letter immediately after sticking.
No. To inform the main operation, press the platen roller button to press the platen roller against the paper core, and start the roll paper.

Adhesive Tape Jumbo Roll Rewinding Machine

Automatic rewinding machine speed ratio adjustment method ---


        The rewinding machine is the first station of the production line equipment of the welcoming machine. The good running condition of the rewinding machine directly affects the quality and production efficiency of the post-processing welcoming paper. The rewinding machine should be able to operate normally and in a good production state. In addition to the good and non-damage of the components, the reasonable adjustment and control of the transmission ratio of the whole machine is very important.
        When the rewinding machine is produced, the original paper web is conveyed by five transmission rollers and belts, that is, a paper feeding belt, a curved roller, a rear platen roller, a front platen roller, a winding roller, and the like. Each of the base papers is thin, the elongation is limited, and the transmission speed ratio is unstable, and the paper web is easy to wrinkle and be broken during the continuous acceleration and deceleration operation of the winder. Reasonable adjustment and control of the speed of each drive roller and paper feed belt can greatly reduce the phenomenon that the paper web is broken. After many daily adjustments, the author summarizes the following key adjustment methods. 1. Stable paper feed belt conveys the line speed of the original paper web. The paper feeding belt of the rewinding machine is driven by the V-belt through the stepless speed-regulating wheel. When the output torque is large, the driving V-belt is close to the outer edge of the speed-regulating wheel, and the transmission speed will be more stable. In order to achieve such a stable transmission effect, the speed ratio of the main gearbox can be adjusted step by step to make the speed of the winding roller slower, and at the same time adjust the speed control handwheels of the paper feed belt of the original paper frame, so that the three sets of transmission triangle belts are in The outer edge of the stepless speed regulation wheel is in a reasonable position until the winding speed of the winding roller and the paper feeding belt are the same.

Adhesive Tape Jumbo Roll Rewinding Machine

Automatic rewinding machine speed ratio adjustment method ---

2. Adjust the paper-pressing gap of the platen roller so that the paper web can be smoothly conveyed between the paper feeding belt and the winding roller. The rear platen roller is the intermediate link of the paper web conveying process. If the adjusted gap is too small, the paper web is easy to wrinkle and sag. When the gap is too large, the three layers of paper are not combined together to facilitate delamination and fault, which affects the speed of the paper feed and Rewind quality. When adjusting the paper-pressing roller, the paper-pressing gap should be gradually increased from small to large, so that the paper web can be locked without sag and not drooping.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com