Stretch Film Making Machine

Stretch Film Making Machine

Rewinding Machine operating procedures - Start thread
1The main operator passes the inspection to confirm that the paper core and the size of the paper cut are correct.
The power-on signal informs the operator to prepare the paper. Open the paper feed roller, blower system, and paper positioning system before threading.
2. Start the rewinding machine and crawl the car at a speed of 15 meters.
3. The base paper is torn or folded into a triangle and sent to the platen roller to be delivered by the platen roller.
The paper is fed to the bottom knife roll and pressed against the horizontal roller.
4. The paper web is drawn flat and the paper trimming is aligned with the paper core and the port.
Introduce the paper edge fan to inform the main operation to stop. At this time, check the trimming situation and adjust it in time.
5. Use a piece of tape to match the paper web to the paper core, and then remove the letter immediately after sticking.
No. To inform the main operation, press the platen roller button to press the platen roller against the paper core, and start the roll paper.

Stretch Film Making Machine

Design and application of constant tension and load distribution control for winder---

1. Rewinder structure and working principle

1.2 Working principle
The paper web is taken out from the paper take-off roller (in this paper, the lower paper feeding method is adopted), and the paper guide roller passes through the slitting mechanism, and is wound from the bottom between the front and rear bottom rollers, and then wound on the paper core. There are 1 support rollers in front of and behind the slitting mechanism, and the front and rear support rollers are equipped with tension sensors for measuring the tension of the web. The platen roller above the core ensures the hardness of the roll. Each component of the winder is driven by a separate motor. The working principle is 3: the original paper roll taken from the paper machine is placed on the unwinding roller, and the brake on the unwinding roller maintains a certain tension of the paper web, and Quickly brake the paper roll when the head is broken. The paper web passes through the guiding roller to reach the slitting device, and several slitting circular cutters divide the paper into the required width, and then send it to the take-up roller for rewinding. After reaching the specified length, the paper is stopped and replaced with a new paper core. Repeat the above process. The main structural parameters of the winder are the width of the paper that can be processed and the maximum speed, followed by the maximum diameter of the paper and roll, the method of cutting and the length.
It can be seen from the working principle of the winder that the motor of the take-up roller drives the corresponding take-up roller to rotate the paper-wound paper core, the diameter of the paper roll gradually increases, and the axial center of the paper roll increases with the diameter. Gradually moving up, the platen roller moves up and gradually reduces the pressure. The unwinding motor mainly provides a reverse torque, creating tension on the paper surface, keeping the paper web flat, and the speed control of the unwinding motor is a process of gradually increasing speed, but the linear speed of the paper web remains unchanged.

Stretch Film Making Machine

Design and application of constant tension and load distribution control for winder---

4.1 Research significance
The significance of this paper is to apply advanced field bus and frequency conversion technology to the traditional paper industry, making the rewinder control system very practical and advanced for a long time.
Firstly, the new Profibus field bus is used to replace the system's large number of I/O wiring, which effectively avoids the interference of the signal; the OP operation panel is used to replace the analog secondary instrument and switch button of the original system. The control system is divided into two levels: the monitoring machine (operator panel) and the field control level (lower position machine). Through the system, the operator can timely understand the various operating states of the winder through the OP panel, analyze the cause of the fault, and make corresponding adjustments and controls on the OP panel according to the site conditions in time. The new control system adopts the frequency conversion control technology, which abandons the DC rotation control mode of the original system of the winder. The application of the frequency conversion technology improves the speed and control precision of the system. The modified vehicle speed reaches 1200m/min (line speed), which is the original system. Twice, at the highest speed, the speed error does not exceed 2%. The friendly man-machine interface system can effectively control the entire production process of the winder, realize effective control of key production parameters, ensure safe and stable production, improve economic efficiency, and reduce labor intensity of workers.
Secondly, the implementation scheme of the new control system has strong universality. The software and hardware design and transformation of the general data acquisition system can connect the original system to the field bus, and the design of the tension and load distribution control of the winder The equipment transformation in the paper industry and the cigarette industry has certain reference significance.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com