Jumbo Roll Turret Rewinding Machine

Jumbo Roll Turret Rewinding Machine

Rewinding Machine operating procedures - Start thread
1The main operator passes the inspection to confirm that the paper core and the size of the paper cut are correct.
The power-on signal informs the operator to prepare the paper. Open the paper feed roller, blower system, and paper positioning system before threading.
2. Start the rewinding machine and crawl the car at a speed of 15 meters.
3. The base paper is torn or folded into a triangle and sent to the platen roller to be delivered by the platen roller.
The paper is fed to the bottom knife roll and pressed against the horizontal roller.
4. The paper web is drawn flat and the paper trimming is aligned with the paper core and the port.
Introduce the paper edge fan to inform the main operation to stop. At this time, check the trimming situation and adjust it in time.
5. Use a piece of tape to match the paper web to the paper core, and then remove the letter immediately after sticking.
No. To inform the main operation, press the platen roller button to press the platen roller against the paper core, and start the roll paper.

Jumbo Roll Turret Rewinding Machine

Belt rewinding machine design and working principle ---

rear bottom roller

The movable beam is fixed to the frame. The movement of the platen roller beam moves with the hydraulic cylinder attached to the beam. The platen roller is decoupled from the hydraulic cylinder during the rewinding process. The platen roller also includes a pressure sensor to measure the pressure between the platen roller and the frame.
The platen roller has a position measuring device for providing a position about the platen roller and the diameter of the paper roll. Based on the above information, the hydraulic cylinder moves in accordance with the separation design curve as the diameter of the paper roll continues to increase. The hydraulic cylinder is equipped with a hydraulic hose rupture protection valve to prevent the paper roll from suddenly falling when the hose is damaged.
working principle 
The platen roller provides additional load to the paper roll at the beginning of the rewinding. At a later stage of the rewind, the pressure is released. In the final stage, the platen roller ensures that the paper roll is in place.
During the threading and changing process, the platen roller is raised to the rear of the safety lock at the top position. The safety lock prevents the platen roller from suddenly falling when the device malfunctions. The platen roller is automatically decompressed when the platen roller is lowered to the core or the base. If the lowering control is terminated before decompression, the platen roller will be activated and the platen roller will be raised to the upper position.
During the rewinding process, the contact surface between the platen roller and the paper core must be carefully observed. If the platen roller is very close to the core, special care must be taken during the rewinding process. If the core starts to vibrate, the speed must be lowered immediately. There is a vibration indicator on the pressing roller beam to facilitate speed reduction in that case.

Jumbo Roll Turret Rewinding Machine

Belt rewinding machine design and working principle ---

3. Platen roller power:
A motor that drives the platen roller by a timing belt drive is mounted on the platen roller beam. The coupling between the individual bearings of the platen roller ensures that the speed of each combined reel is the same. The speed of each part of the platen roller is the same during operation.
Platen roller photocell:
There is a photocell at the end of the platen roller beam. If the paper or any other obstacle enters the photocell illumination area, the photocell signal will immediately stop the downward movement of the platen roller. During operation, the photocell's monitoring paper does not wrap around the platen roller. If something happens, the photoelectric signal activates the alarm to stop the rewind.
Core device:
1-trache
2- top core head
3- drive motor
4- positioning stop pin
5- Safety lock in the top core lock
The core between the drums is locked before the rewinding process begins. Keep the paper roll in place during the running of the paper core locking process.
Construction
The core lock device includes a paper core plug, a cone, and a sleeve. The core of the paper core is fixed in a core seat that can be vertically up and down and can reduce friction. The core of the paper core is supported by the upper bearing of the cone, so it rotates freely. The locking of the core and the upward movement of the core locking device are done hydraulically. The vertically moving hydraulic cylinder supports the weight of the core collet so that the home can rise as the diameter of the paper roll increases. The change in the slit width is adjusted with the help of the hydraulic transfer knob. The paper core collet has a relatively low position on the locating pin. As the paper core model changes, the latch and the paper roll chuck must change. The core collet structure has a shock absorber that is lowered onto the positioning stop pin at the core of the paper core. The safety lock has a compressed air cylinder open.
working principle 
Before the rewinding begins, the collet is knocked into the paper core. The locking cylinder of the operating side core collet has a locking pressure that is less than the drive side. If the core is too long, the operating side cylinder will retract. As the size of the paper roll continues to increase, the paper core collet moves with the paper roll, preventing the paper roll from moving laterally.
Before the paper roll is pushed away from the winder, the paper core chuck is unlocked and moved to the upper position. The appropriateness of the width of the paper core collet is related to the cutter positioning device. The sensor mounted in the paper core chuck records the pulse as the spool rotates. These pulse signals are not used to calculate the paper roll diameter. There is a sensor in each side of the cone. If one side of the sensor is damaged, the other side can be used immediately.
 

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com