Samll Film Winding Machine

Samll Film Winding Machine

Rewinding Machine operating procedures -  Start roll paper
1. The main operation starts the power-on signal and enters the roll paper state.
2. First set the information (length, diameter) of the paper roll to be rewinded.
The tightness of the paper roll adjusts the amount of tension.
3. Generally, the starting speed of the roll paper is set between 30 and 50 meters.
Step up speed, while speeding up, pay close attention to the subtle realization of the roll paper surface, such as pleats, twisting, knife edge biting, etc., should be adjusted in time to ensure the quality of the roll.
4. When the rewinder is in the normal roll, the paper will suddenly be broken due to paper disease or other reasons. The main operation will immediately press the stop button.
5. Connector
5.1. After the rewinder is stopped, first find the cause of the broken broach, make a broken record, and strip the external waste paper of the roll;
5.2. Instructing the main operation to start the paper feed;
5.3. After the paper web is placed on the paper, the paper is broken at the end of the paper and folded with a knife.
5.4. Pull the tape off and place it under the cut paper web. The length of the tape is two centimeters on both sides of the paper web. Cut it with a blade, then use the hand to pull it up to get the paper web to be pulled up and flattened, taped on the tape, paper. Align the interface, cut the long paper web with a knife, and finally level the adhesive tape with your hand. Immediately after the completion, remove the handle and notify the main operation to lower the platen roller and start the roll paper.
6. The main operation is strictly controlled according to the diameter and length required by the process standard. When the length standard is reached, the vehicle speed can be smoothly decelerated and the rewinding is completed.

Samll Film Winding Machine

Rewinding Machine safety operation guide - 

Seventh, production operations and quality control during the rewinding process:

4, pay attention to the quality of the rewinding of the paper roll when rewinding, found zigzag, knife, running,
If the color difference is serious, skipping, chain printing, wrinkling, violent edge, etc., the result should be stopped in time. Only after the inspector confirms can the machine be re-rolled.
5. When the rewinding operation is running, the host must be at the console, and must not leave at will to prevent accidents. Transport
The speed of lifting and lowering is slow, and the speed of the vehicle cannot exceed the prescribed limit.
6. When loading the paper core tube, it is necessary to select the paper core with the same outer diameter and the length specification in line with the quality standard.
The installation of the cylinder requires a large deviation of the outer diameter and needs to be replaced.

Samll Film Winding Machine

Rewinding Machine operation safety regulations - 

Second, the operation steps:
1. According to the production order of the day, the squad leader is responsible for arranging the material production (base paper, packaging materials, paper core);
2. Check whether the quality of the original paper texture, color, tension, elongation and other products meet the product requirements.
3. Put the original paper on the paper-removing shaft and the shaft plug must be locked. The 1575 rewinding machine is assisted by the handyman to push the original paper to the unloading frame and push it into the positioning slot. The 2900 rewinding machine uses the cylinder to lift the paper. Push the rear frame into the positioning groove of the rear frame (when the iron shaft is pushed into the positioning groove, pay attention to safety), and adjust the left and right position. When replacing the base paper, the shaft stalk and the plug must be removed with both hands and placed on the ground. It is strictly forbidden to throw or fall on the ground, and damage the floor or hurt the person;

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com