Adhesive Tapes Jumbo Roll Rewinding Machine

Adhesive Tapes Jumbo Roll Rewinding Machine

Rewinding Machine operating procedures -  Start roll paper
1. The main operation starts the power-on signal and enters the roll paper state.
2. First set the information (length, diameter) of the paper roll to be rewinded.
The tightness of the paper roll adjusts the amount of tension.
3. Generally, the starting speed of the roll paper is set between 30 and 50 meters.
Step up speed, while speeding up, pay close attention to the subtle realization of the roll paper surface, such as pleats, twisting, knife edge biting, etc., should be adjusted in time to ensure the quality of the roll.
4. When the rewinder is in the normal roll, the paper will suddenly be broken due to paper disease or other reasons. The main operation will immediately press the stop button.
5. Connector
5.1. After the rewinder is stopped, first find the cause of the broken broach, make a broken record, and strip the external waste paper of the roll;
5.2. Instructing the main operation to start the paper feed;
5.3. After the paper web is placed on the paper, the paper is broken at the end of the paper and folded with a knife.
5.4. Pull the tape off and place it under the cut paper web. The length of the tape is two centimeters on both sides of the paper web. Cut it with a blade, then use the hand to pull it up to get the paper web to be pulled up and flattened, taped on the tape, paper. Align the interface, cut the long paper web with a knife, and finally level the adhesive tape with your hand. Immediately after the completion, remove the handle and notify the main operation to lower the platen roller and start the roll paper.
6. The main operation is strictly controlled according to the diameter and length required by the process standard. When the length standard is reached, the vehicle speed can be smoothly decelerated and the rewinding is completed.

Adhesive Tapes Jumbo Roll Rewinding Machine

Rewinding Machine operating procedures - 

First, the boot process:
1. Turn on the total power of the rewinder and the power of the detection system in turn; Note: (1) Before turning on the power, please make sure that the circuit is connected correctly and there is no short circuit;
(2) When the main power is turned on, an alarm will occur. After about 5 seconds, after resetting through the touch screen, turn on the detection power.
2. Turn on the air source switch, please ensure that the air pressure is around 6Mpa;
3. According to the paper-feeding direction in the machine state of the touch screen, the product is paper-punched; Note: (1) Please select the paper-feeding state before putting on paper;
(2) Ensure that the core is in the middle position of the inflation shaft, and the core is installed on the left and right gas rise shaft
The same location;

Adhesive Tapes Jumbo Roll Rewinding Machine

Rewinding Machine operation safety regulations - 

Fourth, other requirements in the production process
1. Rolling paper or paper jam of a certain part of the machine must be stopped. Use the jog function to remove the paper. The original paper should be carefully operated when it passes through the embossing device, the crimping device, the paper feed roller and the punching knife. It is strictly prohibited when the machine is running. Wipe and refuel the rotating parts in the state to avoid injury accidents;
2. During the production process, the gears, pulleys, chains and other components of the machine must not be allowed to entangle with paper scraps, ropes, etc., and the air pipe must not leak. The trachea, electric wires, etc. can not be fixed with rope or adhesive tape, which affects the appearance;

3. The waste paper can not be thrown anywhere in the production process, must be loaded into the designated waste paper bag to keep the production site clean.
4. The original paper core produced during the production process must be placed in the designated place;

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com