China Adhesive Tape Winder

China Adhesive Tape Winder

Rewinding Machine operating procedures -  Start roll paper
1. The main operation starts the power-on signal and enters the roll paper state.
2. First set the information (length, diameter) of the paper roll to be rewinded.
The tightness of the paper roll adjusts the amount of tension.
3. Generally, the starting speed of the roll paper is set between 30 and 50 meters.
Step up speed, while speeding up, pay close attention to the subtle realization of the roll paper surface, such as pleats, twisting, knife edge biting, etc., should be adjusted in time to ensure the quality of the roll.
4. When the rewinder is in the normal roll, the paper will suddenly be broken due to paper disease or other reasons. The main operation will immediately press the stop button.
5. Connector
5.1. After the rewinder is stopped, first find the cause of the broken broach, make a broken record, and strip the external waste paper of the roll;
5.2. Instructing the main operation to start the paper feed;
5.3. After the paper web is placed on the paper, the paper is broken at the end of the paper and folded with a knife.
5.4. Pull the tape off and place it under the cut paper web. The length of the tape is two centimeters on both sides of the paper web. Cut it with a blade, then use the hand to pull it up to get the paper web to be pulled up and flattened, taped on the tape, paper. Align the interface, cut the long paper web with a knife, and finally level the adhesive tape with your hand. Immediately after the completion, remove the handle and notify the main operation to lower the platen roller and start the roll paper.
6. The main operation is strictly controlled according to the diameter and length required by the process standard. When the length standard is reached, the vehicle speed can be smoothly decelerated and the rewinding is completed.

China Adhesive Tape Winder

Four release and one rewinding machine operation program ---

Second, the machine starts
1. Press the warning button and delay for about 2 seconds. At the same time, the alarm sounds, and then press the start button to start the machine.
2. When the machine starts, fine-tune the discharge roller to ensure that the material is flush at the receiving roller. During the fine adjustment process, the gear is not rubbed against the periphery.
3. When the machine is running, no objects are allowed between the ultrasonic probe and the material axis. This will cause the machine to stop working.


Third, automatic acceleration
When the accelerator button is pressed and delayed for about 3 seconds, the machine automatically accelerates to the required maximum speed (set in the touch screen), and the deceleration button is pressed once during the acceleration process to automatically accelerate and stop.

China Adhesive Tape Winder

Rewinder mechanical structure and control process ---

 

Second, the main structure of the winder

2.3 Rolling Department

3, unloader
Nowadays, with the increase of the speed of the winder, most of the winders are equipped with unloaders, which are used to push the rolled paper rolls from the support rolls and unload them on the ground. It has many forms, the most common ones are the unwinding station and the unwinding pendulum. Its control mainly depends on air pressure or hydraulic pressure. The thief of the unwinder can be selected according to the number of operators, the size and quality of the core. The advanced foreign rewinding machine can automatically control the positioning of the mandrel and mandrel and the cutting of the paper, which can save auxiliary operation time and improve production efficiency.
4, transmission mechanism
The speed of the paper-feeding machine of the winder is generally about 15 to 40 m/min. In the process of raising the speed of the paper from low, we require the speed of the vehicle to rise, so that the paper roll can be avoided due to the fluctuation of the tension. The tightness is inconsistent. Uniform acceleration is required for breakage or shutdown. During the acceleration process, the average acceleration is usually 0.23~0.37m/s, and the acceleration time is usually 50~60s. In the braking process, the deceleration is 0.42~0.75m/s and the braking time is 40s. In order to meet the shifting requirements of the winder, most of the rewinding opportunities are driven by DC motors. In the previous rewinding system, a DC motor generally controlled two supporting rollers, and in the current rewinding machine, Development and research have started with two separate motor control rolls, which can control the speed difference between the two rolls, which is beneficial for taking up the appropriate tightness of the paper roll.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com