Double Shafts Rewinder

Double Shafts Rewinder

Rewinding Machine operating procedures -  Start roll paper
1. The main operation starts the power-on signal and enters the roll paper state.
2. First set the information (length, diameter) of the paper roll to be rewinded.
The tightness of the paper roll adjusts the amount of tension.
3. Generally, the starting speed of the roll paper is set between 30 and 50 meters.
Step up speed, while speeding up, pay close attention to the subtle realization of the roll paper surface, such as pleats, twisting, knife edge biting, etc., should be adjusted in time to ensure the quality of the roll.
4. When the rewinder is in the normal roll, the paper will suddenly be broken due to paper disease or other reasons. The main operation will immediately press the stop button.
5. Connector
5.1. After the rewinder is stopped, first find the cause of the broken broach, make a broken record, and strip the external waste paper of the roll;
5.2. Instructing the main operation to start the paper feed;
5.3. After the paper web is placed on the paper, the paper is broken at the end of the paper and folded with a knife.
5.4. Pull the tape off and place it under the cut paper web. The length of the tape is two centimeters on both sides of the paper web. Cut it with a blade, then use the hand to pull it up to get the paper web to be pulled up and flattened, taped on the tape, paper. Align the interface, cut the long paper web with a knife, and finally level the adhesive tape with your hand. Immediately after the completion, remove the handle and notify the main operation to lower the platen roller and start the roll paper.
6. The main operation is strictly controlled according to the diameter and length required by the process standard. When the length standard is reached, the vehicle speed can be smoothly decelerated and the rewinding is completed.

Double Shafts Rewinder

Guolian High Speed ??Slitting Rewinder Technical Description ---

The specific technical structure is described as follows:

3. Double curved roller section:
Mainly composed of bracket, double arc roller, worm gear adjustment device, angle gear, air motor and other devices
        After cutting the paper, it enters a set of curved roller stretching assembly, which is mainly composed of two curved rollers and an adjusting mechanism. The adjusting mechanism is driven by a pneumatic motor, and through a set of angular gear mechanism and two sets of worm gear reduction mechanisms, according to The wrap angle between the web and the curved roller needs to be adjusted at any time. The curved roller is introduced from abroad to ensure its performance. This system effectively stretches the web, eliminates wrinkles, and separates the paper rolls.
4. Automatic paper feeding department:
The guiding paper-feeding roller and the compressed air and the guiding plate are adopted, so that the paper head can smoothly and quickly and accurately complete the paper-feeding action on the uniform air cushion generated by the guiding plate and the compressed air, and between the two bottom rollers is used between the conveyor belt and the bottom roller. Friction drive, so that the paper head is close to the surface of the bottom roller, and the paper-feeding action is completed under the action of compressed air.

Double Shafts Rewinder

Guolian Small Winder Introduction---

First, the function: a variety of tape defective products re-rolled
Second, the characteristics:
A. The take-up shaft is driven by a DC 1HP motor and can be steplessly changed.
B. Automatic counting, convenient for setting the length of the winding.
C. The rewinding tension is adjusted by the spring, and the tension adjustment is convenient.
D. The structure of the machine is light and compact, and it is a desktop device, which is convenient to move.

Third, the specifications
1. Roller surface width: 105mm
2. Maximum discharge diameter: standard is 150mm and length is 400mm
3. Take-up diameter: Ø76mm-300mm
4. Rewind width: 12mm-100mm lengthening type is 300mm
5. Take the paper heart: paper tube 3”
6. Mechanical speed: 0~150M/min per minute

Fourth, the host configuration
1. Discharge shaft: 3" movable type (1)
2. Dispensing rack: lengthened 300mm diameter (1)
3. Main motor: DC motor 1HP (1 set)
4. Take-up tension: Spring control (1 set)
5. Length control: four-digit electronic counter (1 group)
6. Take-up shaft: 3" tube core (1 group)

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com