Semi-Auto -Rewinder

Semi-Auto -Rewinder

Rewinding Machine operating procedures -  Start roll paper
1. The main operation starts the power-on signal and enters the roll paper state.
2. First set the information (length, diameter) of the paper roll to be rewinded.
The tightness of the paper roll adjusts the amount of tension.
3. Generally, the starting speed of the roll paper is set between 30 and 50 meters.
Step up speed, while speeding up, pay close attention to the subtle realization of the roll paper surface, such as pleats, twisting, knife edge biting, etc., should be adjusted in time to ensure the quality of the roll.
4. When the rewinder is in the normal roll, the paper will suddenly be broken due to paper disease or other reasons. The main operation will immediately press the stop button.
5. Connector
5.1. After the rewinder is stopped, first find the cause of the broken broach, make a broken record, and strip the external waste paper of the roll;
5.2. Instructing the main operation to start the paper feed;
5.3. After the paper web is placed on the paper, the paper is broken at the end of the paper and folded with a knife.
5.4. Pull the tape off and place it under the cut paper web. The length of the tape is two centimeters on both sides of the paper web. Cut it with a blade, then use the hand to pull it up to get the paper web to be pulled up and flattened, taped on the tape, paper. Align the interface, cut the long paper web with a knife, and finally level the adhesive tape with your hand. Immediately after the completion, remove the handle and notify the main operation to lower the platen roller and start the roll paper.
6. The main operation is strictly controlled according to the diameter and length required by the process standard. When the length standard is reached, the vehicle speed can be smoothly decelerated and the rewinding is completed.

Semi-Auto -Rewinder

Guolian High Speed ??Slitting Rewinder Technical Description ---

Part II: Hydraulic and pneumatic parts:

, pneumatic system
Components for pneumatic systems use brand-name products. Pneumatic control section includes
1) Paper feeding device 2) Paper cutting device 3) Pressure roller lifting ratchet protection device
4) Paper roller frame lifting ratchet protection device 5) Curved roller group angle adjustment
6) Safety protection devices, etc.


Part III: Electrical Section
First, the performance introduction
1. Transmission system adopts AC sub-transmission, with rectification feedback unit and common DC
Busbar and inverter unit + variable frequency motor.
2. Tension detection and tension closed-loop control system, paper roll tension control system.
3. Pressure detection and pressure closed-loop control system of pressure roller.
4. Security protection system. 5. Paper roll diameter measurement.

Semi-Auto -Rewinder

Automatic rewinding machine speed ratio adjustment method ---


        The rewinding machine is the first station of the production line equipment of the welcoming machine. The good running condition of the rewinding machine directly affects the quality and production efficiency of the post-processing welcoming paper. The rewinding machine should be able to operate normally and in a good production state. In addition to the good and non-damage of the components, the reasonable adjustment and control of the transmission ratio of the whole machine is very important.
        When the rewinding machine is produced, the original paper web is conveyed by five transmission rollers and belts, that is, a paper feeding belt, a curved roller, a rear platen roller, a front platen roller, a winding roller, and the like. Each of the base papers is thin, the elongation is limited, and the transmission speed ratio is unstable, and the paper web is easy to wrinkle and be broken during the continuous acceleration and deceleration operation of the winder. Reasonable adjustment and control of the speed of each drive roller and paper feed belt can greatly reduce the phenomenon that the paper web is broken. After many daily adjustments, the author summarizes the following key adjustment methods. 1. Stable paper feed belt conveys the line speed of the original paper web. The paper feeding belt of the rewinding machine is driven by the V-belt through the stepless speed-regulating wheel. When the output torque is large, the driving V-belt is close to the outer edge of the speed-regulating wheel, and the transmission speed will be more stable. In order to achieve such a stable transmission effect, the speed ratio of the main gearbox can be adjusted step by step to make the speed of the winding roller slower, and at the same time adjust the speed control handwheels of the paper feed belt of the original paper frame, so that the three sets of transmission triangle belts are in The outer edge of the stepless speed regulation wheel is in a reasonable position until the winding speed of the winding roller and the paper feeding belt are the same.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com