Adhesive Tape Turret Rewinding Machine

Adhesive Tape Turret Rewinding Machine

Rewinding Machine operating procedures -  Start roll paper
1. The main operation starts the power-on signal and enters the roll paper state.
2. First set the information (length, diameter) of the paper roll to be rewinded.
The tightness of the paper roll adjusts the amount of tension.
3. Generally, the starting speed of the roll paper is set between 30 and 50 meters.
Step up speed, while speeding up, pay close attention to the subtle realization of the roll paper surface, such as pleats, twisting, knife edge biting, etc., should be adjusted in time to ensure the quality of the roll.
4. When the rewinder is in the normal roll, the paper will suddenly be broken due to paper disease or other reasons. The main operation will immediately press the stop button.
5. Connector
5.1. After the rewinder is stopped, first find the cause of the broken broach, make a broken record, and strip the external waste paper of the roll;
5.2. Instructing the main operation to start the paper feed;
5.3. After the paper web is placed on the paper, the paper is broken at the end of the paper and folded with a knife.
5.4. Pull the tape off and place it under the cut paper web. The length of the tape is two centimeters on both sides of the paper web. Cut it with a blade, then use the hand to pull it up to get the paper web to be pulled up and flattened, taped on the tape, paper. Align the interface, cut the long paper web with a knife, and finally level the adhesive tape with your hand. Immediately after the completion, remove the handle and notify the main operation to lower the platen roller and start the roll paper.
6. The main operation is strictly controlled according to the diameter and length required by the process standard. When the length standard is reached, the vehicle speed can be smoothly decelerated and the rewinding is completed.

Adhesive Tape Turret Rewinding Machine

Guolian High Speed ??Slitting Rewinder Technical Description ---

Second, the system configuration
1. Main transmission part: 1 set of paper-removing brake generator, 400kW (YVP4501-6 or
1LA8357-6), one roller motor (YVP225S-4), 37kW, two pressure roller motors (YVP132S-4), 5.5kW, two coiling motors (YVP355L2-4) (one for each front and rear roller) , 315kW, 6 paper cutter motor, 0.55kW, total installed capacity 1082kw (model and power are subject to final design). The rectification feedback and the inverter unit and the tension controller matched with the above constitute a transmission control system.
2. Logic control part: PLC host 1 block.
3. The logic control system selects the S7-400 series products of SIEMENS.
4. Tension control part: 1 set of tension detection and control system, using Sweden
NOBEL products.
5. 1 set of coiling roller pressure detection and control system.
6. The diameter detecting sensor of the take-up roller.
7, with position detection, pressure detection, liquid level detection, safety detection sensor and phase
The control agency should be controlled.
8. On-site operation panel, logic control panel, and electric drive panel.

Adhesive Tape Turret Rewinding Machine

Automatic rewinding machine speed ratio adjustment method ---

2. Adjust the paper-pressing gap of the platen roller so that the paper web can be smoothly conveyed between the paper feeding belt and the winding roller. The rear platen roller is the intermediate link of the paper web conveying process. If the adjusted gap is too small, the paper web is easy to wrinkle and sag. When the gap is too large, the three layers of paper are not combined together to facilitate delamination and fault, which affects the speed of the paper feed and Rewind quality. When adjusting the paper-pressing roller, the paper-pressing gap should be gradually increased from small to large, so that the paper web can be locked without sag and not drooping.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com