Log Roll Adhesive Tape Making Machine

Log Roll Adhesive Tape Making Machine

Rewinding Machine operating procedures -  Start roll paper
1. The main operation starts the power-on signal and enters the roll paper state.
2. First set the information (length, diameter) of the paper roll to be rewinded.
The tightness of the paper roll adjusts the amount of tension.
3. Generally, the starting speed of the roll paper is set between 30 and 50 meters.
Step up speed, while speeding up, pay close attention to the subtle realization of the roll paper surface, such as pleats, twisting, knife edge biting, etc., should be adjusted in time to ensure the quality of the roll.
4. When the rewinder is in the normal roll, the paper will suddenly be broken due to paper disease or other reasons. The main operation will immediately press the stop button.
5. Connector
5.1. After the rewinder is stopped, first find the cause of the broken broach, make a broken record, and strip the external waste paper of the roll;
5.2. Instructing the main operation to start the paper feed;
5.3. After the paper web is placed on the paper, the paper is broken at the end of the paper and folded with a knife.
5.4. Pull the tape off and place it under the cut paper web. The length of the tape is two centimeters on both sides of the paper web. Cut it with a blade, then use the hand to pull it up to get the paper web to be pulled up and flattened, taped on the tape, paper. Align the interface, cut the long paper web with a knife, and finally level the adhesive tape with your hand. Immediately after the completion, remove the handle and notify the main operation to lower the platen roller and start the roll paper.
6. The main operation is strictly controlled according to the diameter and length required by the process standard. When the length standard is reached, the vehicle speed can be smoothly decelerated and the rewinding is completed.

Log Roll Adhesive Tape Making Machine

Design and application of constant tension and load distribution control for winder---

4 Research significance and content
Due to the application and development of frequency conversion technology and computer network technology in the field of industrial control, the establishment of AC drive control system based on field bus has become an effective way to solve the above shortcomings and limitations. Taking PLC as the control unit, the inverter is the execution unit, and the OP operation panel is the operating unit to form the all-digital field bus rewinder AC rotation control system. Based on this assumption, in order to reduce the investment, the original mechanical part and hydraulic part of the system are basically maintained, the original DC rotating system is transformed into an AC rotating system, the solenoid valve and some worn mechanical parts are replaced; and the OP270 man-machine interface is used instead of the machine. Buttons and analog meters, and a part of the mechanical buttons, so that workers can operate on the OP270 or on the console buttons, complement each other, increasing the flexibility of operation.

Log Roll Adhesive Tape Making Machine

Belt rewinding machine design and working principle ---

5:Unloading table action
1- Unloading table rise position
2- Middle position of the unloader
The unloading station transfers the paper roll from the winder to the ground.
Construction
The unloader is a device mounted on the floor to remove the paper roll. The platform is controlled by a hydraulic cylinder. The platform is a steel structure. The platform hydraulic unit is equipped with a load relief valve. These are to ensure the control process of the unloading roll.
working principle 
When the paper roll is advanced onto the platform in the upper position, the platform unloads the paper roll to the intermediate position and then onto the floor, and the paper roll rolls off the platform. For safety reasons, the platform will not automatically unload paper onto the floor unless it is moved by the operator from the intermediate position to the unloading position. The reel cannot be unloaded to the floor anyway before the new rewind.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com