Log Roll Adhesive Tape Winder

Log Roll Adhesive Tape Winder

Rewinding Machine operating procedures -  Start roll paper
1. The main operation starts the power-on signal and enters the roll paper state.
2. First set the information (length, diameter) of the paper roll to be rewinded.
The tightness of the paper roll adjusts the amount of tension.
3. Generally, the starting speed of the roll paper is set between 30 and 50 meters.
Step up speed, while speeding up, pay close attention to the subtle realization of the roll paper surface, such as pleats, twisting, knife edge biting, etc., should be adjusted in time to ensure the quality of the roll.
4. When the rewinder is in the normal roll, the paper will suddenly be broken due to paper disease or other reasons. The main operation will immediately press the stop button.
5. Connector
5.1. After the rewinder is stopped, first find the cause of the broken broach, make a broken record, and strip the external waste paper of the roll;
5.2. Instructing the main operation to start the paper feed;
5.3. After the paper web is placed on the paper, the paper is broken at the end of the paper and folded with a knife.
5.4. Pull the tape off and place it under the cut paper web. The length of the tape is two centimeters on both sides of the paper web. Cut it with a blade, then use the hand to pull it up to get the paper web to be pulled up and flattened, taped on the tape, paper. Align the interface, cut the long paper web with a knife, and finally level the adhesive tape with your hand. Immediately after the completion, remove the handle and notify the main operation to lower the platen roller and start the roll paper.
6. The main operation is strictly controlled according to the diameter and length required by the process standard. When the length standard is reached, the vehicle speed can be smoothly decelerated and the rewinding is completed.

Log Roll Adhesive Tape Winder

Design and application of constant tension and load distribution control for winder---

4.1 Research significance
The significance of this paper is to apply advanced field bus and frequency conversion technology to the traditional paper industry, making the rewinder control system very practical and advanced for a long time.
Firstly, the new Profibus field bus is used to replace the system's large number of I/O wiring, which effectively avoids the interference of the signal; the OP operation panel is used to replace the analog secondary instrument and switch button of the original system. The control system is divided into two levels: the monitoring machine (operator panel) and the field control level (lower position machine). Through the system, the operator can timely understand the various operating states of the winder through the OP panel, analyze the cause of the fault, and make corresponding adjustments and controls on the OP panel according to the site conditions in time. The new control system adopts the frequency conversion control technology, which abandons the DC rotation control mode of the original system of the winder. The application of the frequency conversion technology improves the speed and control precision of the system. The modified vehicle speed reaches 1200m/min (line speed), which is the original system. Twice, at the highest speed, the speed error does not exceed 2%. The friendly man-machine interface system can effectively control the entire production process of the winder, realize effective control of key production parameters, ensure safe and stable production, improve economic efficiency, and reduce labor intensity of workers.
Secondly, the implementation scheme of the new control system has strong universality. The software and hardware design and transformation of the general data acquisition system can connect the original system to the field bus, and the design of the tension and load distribution control of the winder The equipment transformation in the paper industry and the cigarette industry has certain reference significance.

Log Roll Adhesive Tape Winder

Belt rewinding machine design and working principle ---

6 nipple guardrail
The nip guard is a sturdy mesh protector located between the belt roller and the unloader. The nipple guardrail acts as a protective device during the rewinding process. It prevents contact with rotating sticks.
Construction
The vertically moving fence is controlled by hydraulics. In the upper position, the safety lock prevents the fence from falling. When the guardrail falls, the cylinder compression safety lock opens.
working principle 
The nipple is in the upper position when the reel is stopped. When rewinding, it must fall or the winder cannot be turned on.

7 paper feed roller
The reel is moved from the roll to the unloading station by a hydraulically controlled ejector mounted on the frame.
The minimum roll diameter that the pusher roll can be pushed open but cannot be pushed open with the smallest roll is 400 mm (15.7 in)

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com