Machinery

Machinery

Rewinding Machine operating procedures - Rewinding
Firstly, the switch is automatically turned on, and then the paper is positioned to automatically unload the paper. After the unloading is completed, the main operation uses the box rule to measure the size of the rolled paper and observe the trimming of the end face and the rewinding of each end roll. Whether the end face has a burr.

Machinery

Rewinder mechanical structure and control process ---

As the last process in the papermaking industry, the winder is the fastest running machinery in papermaking machinery. Its speed can reach 1500~1800m/min or even the speed can reach 3000m/min or more. The winder is in the papermaking industry. The important role that can not be ignored, the paper roll from the paper machine must be rewinded by the winder to get the finished paper roll we need, and the quality of the finished paper roll is not only determined by the paper machine, The role of the winder is also of particular importance.

 

The working principle of the winder is to install the large paper roll produced from the paper machine on the paper exit frame of the winder. In order to maintain a certain tension of the paper web, the brake device must be installed on the paper return frame. A brake motor is installed on the paper exit frame. If the paper breaks during the rewinding process, the brake device can also brake quickly to reduce paper loss. The web is cut to the width we need by the slitting roller, the paper guide roller and the winder slitting mechanism, and then re-rolled into a paper roll according to the required tightness and the diameter of the finished paper roll. The main structural parameters of the winder are the width of the paper roll that can be rewinded, the maximum speed that the rewinding machine can reach, the quality of the finished paper roll, the maximum diameter of the ejecting roll and the roll paper, and the method of cutting the paper.

 

There are many types of rewinders, and other devices can be equipped in the rewinder as needed to become a joint machine. The rewinder can basically be divided into the following five types: upper paper rewinder, lower paper rewinder, single roll rewinder, special rewinder and thin paper rewinder. Since the research object of this subject is mainly for the lower threading rewinding machine, the introduction and explanation of the double bottom roller lowering paper rewinding machine will be given.

Machinery

Rewinder mechanical structure and control process ---

Third, the rewinding machine control performance indicators
The rewinder is the last process in the papermaking process. The performance of the rewinder determines the quality of the finished paper roll. A complete rewinder must have the following properties:
1. Adjusting mechanism of pressure of the platen roller
As the rewinder continuously performs rewinding, the diameter of the finished paper roll is gradually increased, and the weight of the finished paper roll is also gradually increasing, so that the contact points of the finished paper roll with the front and rear bottom rolls are also changing. So you can come to a conclusion like this:
If the pressure of the platen roller is kept constant and does not change, the pressure between the contact points of the finished paper roll and the front and rear bottom rolls is not guaranteed to be constant, and the change in the contact point causes the pressure generated between them to change accordingly. Therefore, if we want the paper roll to reach the best form, we must adjust the pressure exerted by the platen roller to compensate for the influence of the above two factors. Only in this way can the pressure between the front and rear bottom rollers and the finished paper roll be guaranteed. Variety.
2, support roller torque program control In the rewinding process of the finished paper roll, in order to obtain high quality finished paper roll, the speed control or the support roller torque should meet certain conditions, if the speed control is used, the support roller The speed between the two should be less than 0.2%. As the diameter of the paper roll increases, the speed of the two supporting rollers must be close. Only in this way can the high quality finished paper roll be rewinded, but some quick checking systems cannot consider this design. 

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com