Computer Slip-Separating Machine

Computer Slip-Separating Machine

Rewinding Machine operating procedures - Rewinding
Firstly, the switch is automatically turned on, and then the paper is positioned to automatically unload the paper. After the unloading is completed, the main operation uses the box rule to measure the size of the rolled paper and observe the trimming of the end face and the rewinding of each end roll. Whether the end face has a burr.

Computer Slip-Separating Machine

Design and application of constant tension and load distribution control for winder---

1. Rewinder structure and working principle

1.2 Working principle
The paper web is taken out from the paper take-off roller (in this paper, the lower paper feeding method is adopted), and the paper guide roller passes through the slitting mechanism, and is wound from the bottom between the front and rear bottom rollers, and then wound on the paper core. There are 1 support rollers in front of and behind the slitting mechanism, and the front and rear support rollers are equipped with tension sensors for measuring the tension of the web. The platen roller above the core ensures the hardness of the roll. Each component of the winder is driven by a separate motor. The working principle is 3: the original paper roll taken from the paper machine is placed on the unwinding roller, and the brake on the unwinding roller maintains a certain tension of the paper web, and Quickly brake the paper roll when the head is broken. The paper web passes through the guiding roller to reach the slitting device, and several slitting circular cutters divide the paper into the required width, and then send it to the take-up roller for rewinding. After reaching the specified length, the paper is stopped and replaced with a new paper core. Repeat the above process. The main structural parameters of the winder are the width of the paper that can be processed and the maximum speed, followed by the maximum diameter of the paper and roll, the method of cutting and the length.
It can be seen from the working principle of the winder that the motor of the take-up roller drives the corresponding take-up roller to rotate the paper-wound paper core, the diameter of the paper roll gradually increases, and the axial center of the paper roll increases with the diameter. Gradually moving up, the platen roller moves up and gradually reduces the pressure. The unwinding motor mainly provides a reverse torque, creating tension on the paper surface, keeping the paper web flat, and the speed control of the unwinding motor is a process of gradually increasing speed, but the linear speed of the paper web remains unchanged.

Computer Slip-Separating Machine

Belt rewinding machine design and working principle ---

1 belt roller device
Structure
The belt and stick set consists of two belt rollers with intermediate and end supports! A rubber support belt surrounds the belt roller. The inner surface of the support belt has a guiding profile that controls the operation of the belt. There is also a correspondingly concave surface on the belt roller. The belt roller has been joined together by a rocker and a hydraulic cylinder from below. The belt tension can be adjusted with a hydraulic cylinder during the winding process.
The motor drives the rear belt roller to run, and the other roller is carried by the belt. The belt roller is equipped with a hydraulic brake system. The belt roller bearing housing is lubricated with lubricating oil. The oil flow and temperature of the lubricating oil system are detected by the sensor. There is a directional blow tube between the two rolls to ensure that no space remains in the space between the two rolls. The lifting device has been installed under the belt. The lifting device is used for changing rolls. The lifting device comprises a hydraulic cylinder and a lifting plate interlocked with the rear bottom roller during the lifting process.
Belt roller unit:
1- bottom roller
2- rear belt roller
3- front belt roller
4- belt
5-belt telescopic hydraulic cylinder

Principle of operation
The core is placed between the back bottom roll and the back belt roll. The paper core is supported at that position throughout the initial crimping process up to a diameter of approximately 500 mm (17.9 in). The over 500 mm (17.9 in) belt begins to support the increasing area of ??the paper roll, and the weight of the roll is reached when the paper roll is particularly large. Mainly supported by a belt.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com