Small Slitting Rewinding Machine

Small Slitting Rewinding Machine

Rewinding Machine operating procedures - Rewinding
Firstly, the switch is automatically turned on, and then the paper is positioned to automatically unload the paper. After the unloading is completed, the main operation uses the box rule to measure the size of the rolled paper and observe the trimming of the end face and the rewinding of each end roll. Whether the end face has a burr.

Small Slitting Rewinding Machine

Design and application of constant tension and load distribution control for winder---

2Rewinder control research status at home and abroad
Rewinding machine is an important papermaking machine. It is usually installed behind the paper machine. Its speed should be 2-3 times of the speed of the paper machine, generally 1500-1800m/min, up to 300om/min. When threading, run at a maximum speed of 1:100. In order to ensure continuous paper and loose paper during the rewinding process, the tension of the paper web must be kept constant; in order to ensure the tight and loose quality inside the finished paper, the load distribution of the front and rear bottom roller motors must be performed. Therefore, the main performance requirements of the rewinder for the electric drive system are long-term linear speed, adjustable speed and wide speed range, and fast response.
The control of the early rewinder is mainly based on DC drive, and the DC control system is composed of discrete components or analog regulators to realize the above control functions. Since the transmission of analog signals requires a one-to-one physical connection, the signal changes slowly, which increases the overhead of computer speed and accuracy, and the anti-interference ability of signal transmission is poor, and paper breakage and wrinkling often occur in the production process. So in the mid-to-late 1980s, the analog regulator was replaced by a digital regulator, and the DC digital control system of the winder appeared. This control system is more stable, reliable and suitable for maintenance than the analog system, and is more suitable for interface with the factory computer. In the mid-1990s, most of the newly-invested rewinders in the domestic paper industry used all-digital DC-speed converters produced abroad, and the more famous ones were the 6RA7O series from Siemens and the 590 series DC-speed converters from Continental Transmission.
Due to the DC motor commutator and the brush, under the stable conditions, the design speed of the winder can only reach 1800m/mni, and the accuracy of the digital regulator is still limited to about 0.08% of the maximum speed, which can not meet the high speed paper. The matching requirements of the machine (the speed of the winder should be 2-3 times the speed of the paper machine). In the early 1980s, European and Japanese developed AC variable frequency speed control devices. This technology was successfully introduced to the United States in the mid-1980s and used in rewinders. The biggest advantage of the AC drive is that the AC motor is simple in construction and reliable in operation, and it requires much less maintenance and repair than DC motors.
 

Small Slitting Rewinding Machine

Belt rewinding machine design and working principle ---

rear bottom roller

The movable beam is fixed to the frame. The movement of the platen roller beam moves with the hydraulic cylinder attached to the beam. The platen roller is decoupled from the hydraulic cylinder during the rewinding process. The platen roller also includes a pressure sensor to measure the pressure between the platen roller and the frame.
The platen roller has a position measuring device for providing a position about the platen roller and the diameter of the paper roll. Based on the above information, the hydraulic cylinder moves in accordance with the separation design curve as the diameter of the paper roll continues to increase. The hydraulic cylinder is equipped with a hydraulic hose rupture protection valve to prevent the paper roll from suddenly falling when the hose is damaged.
working principle 
The platen roller provides additional load to the paper roll at the beginning of the rewinding. At a later stage of the rewind, the pressure is released. In the final stage, the platen roller ensures that the paper roll is in place.
During the threading and changing process, the platen roller is raised to the rear of the safety lock at the top position. The safety lock prevents the platen roller from suddenly falling when the device malfunctions. The platen roller is automatically decompressed when the platen roller is lowered to the core or the base. If the lowering control is terminated before decompression, the platen roller will be activated and the platen roller will be raised to the upper position.
During the rewinding process, the contact surface between the platen roller and the paper core must be carefully observed. If the platen roller is very close to the core, special care must be taken during the rewinding process. If the core starts to vibrate, the speed must be lowered immediately. There is a vibration indicator on the pressing roller beam to facilitate speed reduction in that case.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com