Rewinder Slitter Machine

Rewinder Slitter Machine

Rewinding Machine operating procedures - Rewinding
Firstly, the switch is automatically turned on, and then the paper is positioned to automatically unload the paper. After the unloading is completed, the main operation uses the box rule to measure the size of the rolled paper and observe the trimming of the end face and the rewinding of each end roll. Whether the end face has a burr.

Rewinder Slitter Machine

Design and application of constant tension and load distribution control for winder---

4 Research significance and content
Due to the application and development of frequency conversion technology and computer network technology in the field of industrial control, the establishment of AC drive control system based on field bus has become an effective way to solve the above shortcomings and limitations. Taking PLC as the control unit, the inverter is the execution unit, and the OP operation panel is the operating unit to form the all-digital field bus rewinder AC rotation control system. Based on this assumption, in order to reduce the investment, the original mechanical part and hydraulic part of the system are basically maintained, the original DC rotating system is transformed into an AC rotating system, the solenoid valve and some worn mechanical parts are replaced; and the OP270 man-machine interface is used instead of the machine. Buttons and analog meters, and a part of the mechanical buttons, so that workers can operate on the OP270 or on the console buttons, complement each other, increasing the flexibility of operation.

Rewinder Slitter Machine

Belt rewinding machine design and working principle ---

3. Platen roller power:
A motor that drives the platen roller by a timing belt drive is mounted on the platen roller beam. The coupling between the individual bearings of the platen roller ensures that the speed of each combined reel is the same. The speed of each part of the platen roller is the same during operation.
Platen roller photocell:
There is a photocell at the end of the platen roller beam. If the paper or any other obstacle enters the photocell illumination area, the photocell signal will immediately stop the downward movement of the platen roller. During operation, the photocell's monitoring paper does not wrap around the platen roller. If something happens, the photoelectric signal activates the alarm to stop the rewind.
Core device:
1-trache
2- top core head
3- drive motor
4- positioning stop pin
5- Safety lock in the top core lock
The core between the drums is locked before the rewinding process begins. Keep the paper roll in place during the running of the paper core locking process.
Construction
The core lock device includes a paper core plug, a cone, and a sleeve. The core of the paper core is fixed in a core seat that can be vertically up and down and can reduce friction. The core of the paper core is supported by the upper bearing of the cone, so it rotates freely. The locking of the core and the upward movement of the core locking device are done hydraulically. The vertically moving hydraulic cylinder supports the weight of the core collet so that the home can rise as the diameter of the paper roll increases. The change in the slit width is adjusted with the help of the hydraulic transfer knob. The paper core collet has a relatively low position on the locating pin. As the paper core model changes, the latch and the paper roll chuck must change. The core collet structure has a shock absorber that is lowered onto the positioning stop pin at the core of the paper core. The safety lock has a compressed air cylinder open.
working principle 
Before the rewinding begins, the collet is knocked into the paper core. The locking cylinder of the operating side core collet has a locking pressure that is less than the drive side. If the core is too long, the operating side cylinder will retract. As the size of the paper roll continues to increase, the paper core collet moves with the paper roll, preventing the paper roll from moving laterally.
Before the paper roll is pushed away from the winder, the paper core chuck is unlocked and moved to the upper position. The appropriateness of the width of the paper core collet is related to the cutter positioning device. The sensor mounted in the paper core chuck records the pulse as the spool rotates. These pulse signals are not used to calculate the paper roll diameter. There is a sensor in each side of the cone. If one side of the sensor is damaged, the other side can be used immediately.
 

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com