Rewinding Machine structure - Ejection Department
In the rewinder system, we installed the paper roll on the paper exit frame. In order to ensure that the width of the sides of the paper web is the same, we should be moving the seasoning when
the paper roll is ejected. But the paper roll in the new structure can move with the paper exit frame,
This ensures a greater rigidity of the exit frame. In addition to manually moving the paper roll, we can also use the pneumatic, photoelectric device and electric method to adjust the axial movement
of the paper exit frame, so that the cutting edge of the winder can be narrowed, and the manual adjustment can not be achieved. Requirements.
Design and application of constant tension and load distribution control for winder---
1. Rewinder structure and working principle
1.2 Working principle
The paper web is taken out from the paper take-off roller (in this paper, the lower paper feeding method is adopted), and the paper guide roller passes through the slitting mechanism, and is wound from the bottom between the front and rear bottom rollers, and then wound on the paper core. There are 1 support rollers in front of and behind the slitting mechanism, and the front and rear support rollers are equipped with tension sensors for measuring the tension of the web. The platen roller above the core ensures the hardness of the roll. Each component of the winder is driven by a separate motor. The working principle is 3: the original paper roll taken from the paper machine is placed on the unwinding roller, and the brake on the unwinding roller maintains a certain tension of the paper web, and Quickly brake the paper roll when the head is broken. The paper web passes through the guiding roller to reach the slitting device, and several slitting circular cutters divide the paper into the required width, and then send it to the take-up roller for rewinding. After reaching the specified length, the paper is stopped and replaced with a new paper core. Repeat the above process. The main structural parameters of the winder are the width of the paper that can be processed and the maximum speed, followed by the maximum diameter of the paper and roll, the method of cutting and the length.
It can be seen from the working principle of the winder that the motor of the take-up roller drives the corresponding take-up roller to rotate the paper-wound paper core, the diameter of the paper roll gradually increases, and the axial center of the paper roll increases with the diameter. Gradually moving up, the platen roller moves up and gradually reduces the pressure. The unwinding motor mainly provides a reverse torque, creating tension on the paper surface, keeping the paper web flat, and the speed control of the unwinding motor is a process of gradually increasing speed, but the linear speed of the paper web remains unchanged.
Belt rewinding machine design and working principle ---
rear bottom roller
The movable beam is fixed to the frame. The movement of the platen roller beam moves with the hydraulic cylinder attached to the beam. The platen roller is decoupled from the hydraulic cylinder during the rewinding process. The platen roller also includes a pressure sensor to measure the pressure between the platen roller and the frame.
The platen roller has a position measuring device for providing a position about the platen roller and the diameter of the paper roll. Based on the above information, the hydraulic cylinder moves in accordance with the separation design curve as the diameter of the paper roll continues to increase. The hydraulic cylinder is equipped with a hydraulic hose rupture protection valve to prevent the paper roll from suddenly falling when the hose is damaged.
The platen roller provides additional load to the paper roll at the beginning of the rewinding. At a later stage of the rewind, the pressure is released. In the final stage, the platen roller ensures that the paper roll is in place.
During the threading and changing process, the platen roller is raised to the rear of the safety lock at the top position. The safety lock prevents the platen roller from suddenly falling when the device malfunctions. The platen roller is automatically decompressed when the platen roller is lowered to the core or the base. If the lowering control is terminated before decompression, the platen roller will be activated and the platen roller will be raised to the upper position.
During the rewinding process, the contact surface between the platen roller and the paper core must be carefully observed. If the platen roller is very close to the core, special care must be taken during the rewinding process. If the core starts to vibrate, the speed must be lowered immediately. There is a vibration indicator on the pressing roller beam to facilitate speed reduction in that case.
Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc