Rewinding Machine structure - Ejection Department
In the rewinder system, we installed the paper roll on the paper exit frame. In order to ensure that the width of the sides of the paper web is the same, we should be moving the seasoning when
the paper roll is ejected. But the paper roll in the new structure can move with the paper exit frame,
This ensures a greater rigidity of the exit frame. In addition to manually moving the paper roll, we can also use the pneumatic, photoelectric device and electric method to adjust the axial movement
of the paper exit frame, so that the cutting edge of the winder can be narrowed, and the manual adjustment can not be achieved. Requirements.
Design and application of constant tension and load distribution control for winder---
4.1 Research significance
The significance of this paper is to apply advanced field bus and frequency conversion technology to the traditional paper industry, making the rewinder control system very practical and advanced for a long time.
Firstly, the new Profibus field bus is used to replace the system's large number of I/O wiring, which effectively avoids the interference of the signal; the OP operation panel is used to replace the analog secondary instrument and switch button of the original system. The control system is divided into two levels: the monitoring machine (operator panel) and the field control level (lower position machine). Through the system, the operator can timely understand the various operating states of the winder through the OP panel, analyze the cause of the fault, and make corresponding adjustments and controls on the OP panel according to the site conditions in time. The new control system adopts the frequency conversion control technology, which abandons the DC rotation control mode of the original system of the winder. The application of the frequency conversion technology improves the speed and control precision of the system. The modified vehicle speed reaches 1200m/min (line speed), which is the original system. Twice, at the highest speed, the speed error does not exceed 2%. The friendly man-machine interface system can effectively control the entire production process of the winder, realize effective control of key production parameters, ensure safe and stable production, improve economic efficiency, and reduce labor intensity of workers.
Secondly, the implementation scheme of the new control system has strong universality. The software and hardware design and transformation of the general data acquisition system can connect the original system to the field bus, and the design of the tension and load distribution control of the winder The equipment transformation in the paper industry and the cigarette industry has certain reference significance.
Belt rewinding machine design and working principle ---
3. Platen roller power:
A motor that drives the platen roller by a timing belt drive is mounted on the platen roller beam. The coupling between the individual bearings of the platen roller ensures that the speed of each combined reel is the same. The speed of each part of the platen roller is the same during operation.
Platen roller photocell:
There is a photocell at the end of the platen roller beam. If the paper or any other obstacle enters the photocell illumination area, the photocell signal will immediately stop the downward movement of the platen roller. During operation, the photocell's monitoring paper does not wrap around the platen roller. If something happens, the photoelectric signal activates the alarm to stop the rewind.
2- top core head
3- drive motor
4- positioning stop pin
5- Safety lock in the top core lock
The core between the drums is locked before the rewinding process begins. Keep the paper roll in place during the running of the paper core locking process.
The core lock device includes a paper core plug, a cone, and a sleeve. The core of the paper core is fixed in a core seat that can be vertically up and down and can reduce friction. The core of the paper core is supported by the upper bearing of the cone, so it rotates freely. The locking of the core and the upward movement of the core locking device are done hydraulically. The vertically moving hydraulic cylinder supports the weight of the core collet so that the home can rise as the diameter of the paper roll increases. The change in the slit width is adjusted with the help of the hydraulic transfer knob. The paper core collet has a relatively low position on the locating pin. As the paper core model changes, the latch and the paper roll chuck must change. The core collet structure has a shock absorber that is lowered onto the positioning stop pin at the core of the paper core. The safety lock has a compressed air cylinder open.
Before the rewinding begins, the collet is knocked into the paper core. The locking cylinder of the operating side core collet has a locking pressure that is less than the drive side. If the core is too long, the operating side cylinder will retract. As the size of the paper roll continues to increase, the paper core collet moves with the paper roll, preventing the paper roll from moving laterally.
Before the paper roll is pushed away from the winder, the paper core chuck is unlocked and moved to the upper position. The appropriateness of the width of the paper core collet is related to the cutter positioning device. The sensor mounted in the paper core chuck records the pulse as the spool rotates. These pulse signals are not used to calculate the paper roll diameter. There is a sensor in each side of the cone. If one side of the sensor is damaged, the other side can be used immediately.
Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc