Automatic Machinery Single Shaft Tape Slitting Rewinding Machine

Automatic Machinery Single Shaft Tape Slitting Rewinding Machine

Rewinding Machine Structure - Longitudinal Section
In the mechanical system of the winder, the slitting mechanism is a very important part of the winder. In order to ensure a straight and smooth cutting edge, the quality control of the finished paper roll plays an important role in ensuring the volume. It is easy and can reduce the fluffing during printing.
The slitting mechanism should be installed as close as possible to the paper roll so that it can produce a lateral movement more than necessary during the process of cutting the web without curling.

Automatic Machinery Single Shaft Tape Slitting Rewinding Machine

Rewinder mechanical structure and control process ---

As the last process in the papermaking industry, the winder is the fastest running machinery in papermaking machinery. Its speed can reach 1500~1800m/min or even the speed can reach 3000m/min or more. The winder is in the papermaking industry. The important role that can not be ignored, the paper roll from the paper machine must be rewinded by the winder to get the finished paper roll we need, and the quality of the finished paper roll is not only determined by the paper machine, The role of the winder is also of particular importance.

 

The working principle of the winder is to install the large paper roll produced from the paper machine on the paper exit frame of the winder. In order to maintain a certain tension of the paper web, the brake device must be installed on the paper return frame. A brake motor is installed on the paper exit frame. If the paper breaks during the rewinding process, the brake device can also brake quickly to reduce paper loss. The web is cut to the width we need by the slitting roller, the paper guide roller and the winder slitting mechanism, and then re-rolled into a paper roll according to the required tightness and the diameter of the finished paper roll. The main structural parameters of the winder are the width of the paper roll that can be rewinded, the maximum speed that the rewinding machine can reach, the quality of the finished paper roll, the maximum diameter of the ejecting roll and the roll paper, and the method of cutting the paper.

 

There are many types of rewinders, and other devices can be equipped in the rewinder as needed to become a joint machine. The rewinder can basically be divided into the following five types: upper paper rewinder, lower paper rewinder, single roll rewinder, special rewinder and thin paper rewinder. Since the research object of this subject is mainly for the lower threading rewinding machine, the introduction and explanation of the double bottom roller lowering paper rewinding machine will be given.

Automatic Machinery Single Shaft Tape Slitting Rewinding Machine

Rewinder mechanical structure and control process ---

 

Second, the main structure of the winder

2.3 Rolling Department

3, unloader
Nowadays, with the increase of the speed of the winder, most of the winders are equipped with unloaders, which are used to push the rolled paper rolls from the support rolls and unload them on the ground. It has many forms, the most common ones are the unwinding station and the unwinding pendulum. Its control mainly depends on air pressure or hydraulic pressure. The thief of the unwinder can be selected according to the number of operators, the size and quality of the core. The advanced foreign rewinding machine can automatically control the positioning of the mandrel and mandrel and the cutting of the paper, which can save auxiliary operation time and improve production efficiency.
4, transmission mechanism
The speed of the paper-feeding machine of the winder is generally about 15 to 40 m/min. In the process of raising the speed of the paper from low, we require the speed of the vehicle to rise, so that the paper roll can be avoided due to the fluctuation of the tension. The tightness is inconsistent. Uniform acceleration is required for breakage or shutdown. During the acceleration process, the average acceleration is usually 0.23~0.37m/s, and the acceleration time is usually 50~60s. In the braking process, the deceleration is 0.42~0.75m/s and the braking time is 40s. In order to meet the shifting requirements of the winder, most of the rewinding opportunities are driven by DC motors. In the previous rewinding system, a DC motor generally controlled two supporting rollers, and in the current rewinding machine, Development and research have started with two separate motor control rolls, which can control the speed difference between the two rolls, which is beneficial for taking up the appropriate tightness of the paper roll.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com