High Quality Carton Sealing Packing Tape Rewinding Machine

High Quality Carton Sealing Packing Tape Rewinding Machine

Rewinding Machine Structure - Control Performance Indicators
The rewinder is the last process in the papermaking process. The performance of the rewinder determines the quality of the finished paper roll. A complete rewinder must have the following properties:
1. Adjusting mechanism of pressure of the platen roller
2, support roller torque program control
3. Tension adjustment mechanism
4. Electric drive "flexible" start and proper speed program control.

High Quality Carton Sealing Packing Tape Rewinding Machine

Rewinder mechanical structure and control process ---

 

Second, the main structure of the winder

2.2 Longitudinal section
In the mechanical system of the winder, the slitting mechanism is a very important part of the winder. In order to ensure a straight and smooth cutting edge, the quality control of the finished paper roll plays an important role in ensuring the volume. It is easy and can reduce the fluffing during printing. The slitting mechanism should be installed as close as possible to the paper roll so that it can produce a lateral movement more than necessary during the process of cutting the web without curling.
The high-speed rewinding paper conveying system is also very important in the application. The old-fashioned rewinding machine is mainly handled by manual. With the increase of the speed of the rewinding machine, the manual can no longer be processed. There are two ways to transport the paper side of the reel: fan direct pumping and venturi suction. The direct drawing type of the fan mainly uses a centrifugal fan, and the fan is placed under the floor. The inlet of the fan and the air duct near the longitudinal cutting edge are connected to each other, and the blade of the fan is also equipped with a wind blade. When the fan is sucked, it will be broken by the blade and then sent to the water pulper. However, since the edge of the paper has to pass through the inside of the fan, the blade transported by this type of paper is very worn and needs to be changed frequently. Venturi suction is also used in the high-pressure centrifugal fan, but the paper edge does not pass through the fan, directly the longitudinal cutting edge of the duct into the venturi pipe, the wind machine generates negative pressure in the venturi, and then the paper While washing the venturi tube and then feeding it to the water pulper, the paper edge conveyed at this time is continuous. The disadvantage of this method is that when the speed of the winder is relatively high, the power of the selected fan is large, which will increase the operation. Cost, increase loss.

High Quality Carton Sealing Packing Tape Rewinding Machine

Rewinder mechanical structure and control process ---

 

Second, the main structure of the winder

2.3 Rolling Department

3, unloader
Nowadays, with the increase of the speed of the winder, most of the winders are equipped with unloaders, which are used to push the rolled paper rolls from the support rolls and unload them on the ground. It has many forms, the most common ones are the unwinding station and the unwinding pendulum. Its control mainly depends on air pressure or hydraulic pressure. The thief of the unwinder can be selected according to the number of operators, the size and quality of the core. The advanced foreign rewinding machine can automatically control the positioning of the mandrel and mandrel and the cutting of the paper, which can save auxiliary operation time and improve production efficiency.
4, transmission mechanism
The speed of the paper-feeding machine of the winder is generally about 15 to 40 m/min. In the process of raising the speed of the paper from low, we require the speed of the vehicle to rise, so that the paper roll can be avoided due to the fluctuation of the tension. The tightness is inconsistent. Uniform acceleration is required for breakage or shutdown. During the acceleration process, the average acceleration is usually 0.23~0.37m/s, and the acceleration time is usually 50~60s. In the braking process, the deceleration is 0.42~0.75m/s and the braking time is 40s. In order to meet the shifting requirements of the winder, most of the rewinding opportunities are driven by DC motors. In the previous rewinding system, a DC motor generally controlled two supporting rollers, and in the current rewinding machine, Development and research have started with two separate motor control rolls, which can control the speed difference between the two rolls, which is beneficial for taking up the appropriate tightness of the paper roll.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com