Automatic Rewinidng Machine

Automatic Rewinidng Machine

Rewinding Machine Structure - Control Performance Indicators
The rewinder is the last process in the papermaking process. The performance of the rewinder determines the quality of the finished paper roll. A complete rewinder must have the following properties:
1. Adjusting mechanism of pressure of the platen roller
2, support roller torque program control
3. Tension adjustment mechanism
4. Electric drive "flexible" start and proper speed program control.

Automatic Rewinidng Machine

Design and application of constant tension and load distribution control for winder---

4.1 Research significance
The significance of this paper is to apply advanced field bus and frequency conversion technology to the traditional paper industry, making the rewinder control system very practical and advanced for a long time.
Firstly, the new Profibus field bus is used to replace the system's large number of I/O wiring, which effectively avoids the interference of the signal; the OP operation panel is used to replace the analog secondary instrument and switch button of the original system. The control system is divided into two levels: the monitoring machine (operator panel) and the field control level (lower position machine). Through the system, the operator can timely understand the various operating states of the winder through the OP panel, analyze the cause of the fault, and make corresponding adjustments and controls on the OP panel according to the site conditions in time. The new control system adopts the frequency conversion control technology, which abandons the DC rotation control mode of the original system of the winder. The application of the frequency conversion technology improves the speed and control precision of the system. The modified vehicle speed reaches 1200m/min (line speed), which is the original system. Twice, at the highest speed, the speed error does not exceed 2%. The friendly man-machine interface system can effectively control the entire production process of the winder, realize effective control of key production parameters, ensure safe and stable production, improve economic efficiency, and reduce labor intensity of workers.
Secondly, the implementation scheme of the new control system has strong universality. The software and hardware design and transformation of the general data acquisition system can connect the original system to the field bus, and the design of the tension and load distribution control of the winder The equipment transformation in the paper industry and the cigarette industry has certain reference significance.

Automatic Rewinidng Machine

Belt rewinding machine design and working principle ---

1 belt roller device
Structure
The belt and stick set consists of two belt rollers with intermediate and end supports! A rubber support belt surrounds the belt roller. The inner surface of the support belt has a guiding profile that controls the operation of the belt. There is also a correspondingly concave surface on the belt roller. The belt roller has been joined together by a rocker and a hydraulic cylinder from below. The belt tension can be adjusted with a hydraulic cylinder during the winding process.
The motor drives the rear belt roller to run, and the other roller is carried by the belt. The belt roller is equipped with a hydraulic brake system. The belt roller bearing housing is lubricated with lubricating oil. The oil flow and temperature of the lubricating oil system are detected by the sensor. There is a directional blow tube between the two rolls to ensure that no space remains in the space between the two rolls. The lifting device has been installed under the belt. The lifting device is used for changing rolls. The lifting device comprises a hydraulic cylinder and a lifting plate interlocked with the rear bottom roller during the lifting process.
Belt roller unit:
1- bottom roller
2- rear belt roller
3- front belt roller
4- belt
5-belt telescopic hydraulic cylinder

Principle of operation
The core is placed between the back bottom roll and the back belt roll. The paper core is supported at that position throughout the initial crimping process up to a diameter of approximately 500 mm (17.9 in). The over 500 mm (17.9 in) belt begins to support the increasing area of ??the paper roll, and the weight of the roll is reached when the paper roll is particularly large. Mainly supported by a belt.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com