Reflective Tape Rewinder Machine

Reflective Tape Rewinder Machine

Rewinding Machine common fault - platen roller vibration
1. Proportional valve is unstable - cleaning proportional valve or replacing proportional valve
2. Damage to the top core bearing - Replace the bearing
3. The clearance between the support wheel and the guide rail of the core device is too large - Adjust the clearance (the core is clamped at both ends of the top core, 
and the eccentric shaft of the roller is adjusted to the gap between the roller and the guide rail is 0)
4. Guide rail wear - replace or repair the rail
5. Paper core deformation - Replace the paper core
6. The top core device supports the wheel bearing or the copper sleeve wear - replace the support wheel bearing or copper sleeve
7. The thickness of the paper is different - the production process is solved

Reflective Tape Rewinder Machine

Four release and one rewinding machine operation program ---

Second, the machine starts
1. Press the warning button and delay for about 2 seconds. At the same time, the alarm sounds, and then press the start button to start the machine.
2. When the machine starts, fine-tune the discharge roller to ensure that the material is flush at the receiving roller. During the fine adjustment process, the gear is not rubbed against the periphery.
3. When the machine is running, no objects are allowed between the ultrasonic probe and the material axis. This will cause the machine to stop working.


Third, automatic acceleration
When the accelerator button is pressed and delayed for about 3 seconds, the machine automatically accelerates to the required maximum speed (set in the touch screen), and the deceleration button is pressed once during the acceleration process to automatically accelerate and stop.

Reflective Tape Rewinder Machine

Guolian High Speed ??Slitting Rewinder Technical Description ---

The specific technical structure is described as follows:

2. Paper cutting department:
It is mainly composed of independent frame, guiding paper-feeding roller, segmented and extended arc roller device, front and rear segment guide roller, bottom knife device, round knife device and paper suction fan.
The frame is welded by steel plates and is heavy and sturdy, completely independent of the take-up frame, avoiding the effects of possible vibration on the paper cut.
Guided paper roller, diameter Φ700mm, material Q235, directly driven by motor, chrome-plated surface, hydraulic disc brake and vertical adjustment device, can be adjusted along the scale with worm gear system to adjust the tension of the paper web, adjustment range It is ±25mm. The large diameter guide rollers also facilitate smooth and high speed operation of the equipment and paper web. The bottom knife device, the round knife device and the front and rear segment guide rollers form a paper cutting platform to ensure that the width direction of the paper cutting is even and even. There are 6 sets of cutters, top knife φ180mm, bottom knife φ200mm, each bottom knife is driven by a variable frequency motor, the cutter is automatically positioned, and the cutting servo width is automatically adjusted by the control servo system. The entire slitting system assembly (including tool holders, guide rails, etc.) is imported from abroad to ensure its stability and reliability. The segment guide roller before and after the cutter has a diameter of φ198mm and a roller material Q235, which is divided into 5 sections. Each side of the cutter is equipped with SKF bearings. The surface of the roller body is grooved and the surface is chrome-plated. The circular knife device is composed of a cylinder, a sliding seat and a round knife, and is fixed on the circular beam beam guide rail. The feeding knife and the knife are controlled by the cylinder. After the starting, the two sides of the knife start to cut the paper edge, and the other round knife is given by the operator. After the command is fed, when the paper breaks, the air source of the middle circular knife is automatically cut off by the main control command and automatically raised. There is a web stabilizer plate on each side of the knife to guide the paper edge.
      Before the paper cutting table, a set of segmented stretching roller system is installed. The diameter of the stretching roller is φ198mm, the material of the roller body is Q235, and the surface is chrome-plated. The total length is 19 segments. The curvature of the multi-stage roller can be adjusted before and after the hand wheel to ensure the paper web. smooth.
      The suction paper edge device on both sides of the longitudinal cutter uses a special fan to break the paper edge, which makes the suction effect better, and is also beneficial to the next processing of the waste paper edge. Fan motor power 37KW air volume 11000m3 / h.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com