Transparent Tapes Double Side Adhesive Tape Rewinder Machinery

Transparent Tapes Double Side Adhesive Tape Rewinder Machinery

Rewinding Machine common fault - platen roller vibration
1. Proportional valve is unstable - cleaning proportional valve or replacing proportional valve
2. Damage to the top core bearing - Replace the bearing
3. The clearance between the support wheel and the guide rail of the core device is too large - Adjust the clearance (the core is clamped at both ends of the top core, 
and the eccentric shaft of the roller is adjusted to the gap between the roller and the guide rail is 0)
4. Guide rail wear - replace or repair the rail
5. Paper core deformation - Replace the paper core
6. The top core device supports the wheel bearing or the copper sleeve wear - replace the support wheel bearing or copper sleeve
7. The thickness of the paper is different - the production process is solved

Transparent Tapes Double Side Adhesive Tape Rewinder Machinery

Rewinder mechanical structure and control process ---

 

Second, the main structure of the winder
2.1 Ejection Department
In the rewinder system, we installed the paper roll on the paper exit frame. In order to ensure that the width of the sides of the paper web is the same, we should be moving the seasoning when the paper roll is ejected. However, the paper roll in the new structure can be moved together with the paper exit frame, which ensures greater rigidity of the paper exit frame. In addition to manually moving the paper roll, we can also use the pneumatic, photoelectric device and electric method to adjust the axial movement of the paper exit frame, so that the cutting edge of the winder can be narrowed, and the manual adjustment can not be achieved. Requirements.
We have a coupling on the reel of the unwinding roll. When working, we can use a pneumatic device to connect the brake to the motor. We can know that when the high-speed winder is started, the required acceleration time from zero to 2000m/min can be completed within 50~60s, and the deceleration time required for braking is 40s. Or even shorter, so we need to consider the maximum diameter and the maximum braking speed of the paper-removing brake on the winder to reduce the paper loss of the paper-cut, or it will cause a lot of waste. In the selection of the brakes of the eject roll, we often use brakes for starting brakes, magnetic brakes and mechanical brakes. In the usual case, we use the combination of the brake motor and other brake devices. When we press the paper, the paper roll started by the DC motor can enter the acceleration and working state and can be operated by the braking of the DC motor. Control, the tension control of the paper web, in the case of emergency stop, we can use the DC motor and other brakes together to stop the paper roll at the fastest speed.

Transparent Tapes Double Side Adhesive Tape Rewinder Machinery

Rewinder mechanical structure and control process ---

Third, the rewinding machine control performance indicators
The rewinder is the last process in the papermaking process. The performance of the rewinder determines the quality of the finished paper roll. A complete rewinder must have the following properties:
1. Adjusting mechanism of pressure of the platen roller
As the rewinder continuously performs rewinding, the diameter of the finished paper roll is gradually increased, and the weight of the finished paper roll is also gradually increasing, so that the contact points of the finished paper roll with the front and rear bottom rolls are also changing. So you can come to a conclusion like this:
If the pressure of the platen roller is kept constant and does not change, the pressure between the contact points of the finished paper roll and the front and rear bottom rolls is not guaranteed to be constant, and the change in the contact point causes the pressure generated between them to change accordingly. Therefore, if we want the paper roll to reach the best form, we must adjust the pressure exerted by the platen roller to compensate for the influence of the above two factors. Only in this way can the pressure between the front and rear bottom rollers and the finished paper roll be guaranteed. Variety.
2, support roller torque program control In the rewinding process of the finished paper roll, in order to obtain high quality finished paper roll, the speed control or the support roller torque should meet certain conditions, if the speed control is used, the support roller The speed between the two should be less than 0.2%. As the diameter of the paper roll increases, the speed of the two supporting rollers must be close. Only in this way can the high quality finished paper roll be rewinded, but some quick checking systems cannot consider this design. 

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com