Outdoor Pipeline Sealing Aluminum Coated Tape Rewinder Machine

Outdoor Pipeline Sealing Aluminum Coated Tape Rewinder Machine

Rewinding Machine common fault - platen roller vibration
1. Proportional valve is unstable - cleaning proportional valve or replacing proportional valve
2. Damage to the top core bearing - Replace the bearing
3. The clearance between the support wheel and the guide rail of the core device is too large - Adjust the clearance (the core is clamped at both ends of the top core, 
and the eccentric shaft of the roller is adjusted to the gap between the roller and the guide rail is 0)
4. Guide rail wear - replace or repair the rail
5. Paper core deformation - Replace the paper core
6. The top core device supports the wheel bearing or the copper sleeve wear - replace the support wheel bearing or copper sleeve
7. The thickness of the paper is different - the production process is solved

Outdoor Pipeline Sealing Aluminum Coated Tape Rewinder Machine

Rewinder mechanical structure and control process ---

 

Second, the main structure of the winder

2.3 Rolling Department
1. Stretching device
The stretching device of the rewinder is set to keep the paper web slit after slitting. In some paper cutting knives, the stretcher is also used. The main function is to eliminate the texture and slack of the paper web. Mainly, it can maintain the good operation of slitting. There are three types of stretchers that we often use today: D-shaped stretches, curved rollers, and Z-type double-bar stretchers.
2, support roller
The backup roll is mainly used to support the paper roll, which is composed of a controlled cast iron roll or a general tube roll. The roller body is mainly cast iron pipe and steel pipe, and its diameter is usually 400-700 mm or more according to the width of the winder. The center-to-center ratio between the rolls of the backup roll should be greater than the roll diameter. Only at such a distance, the roll core does not get caught in the middle of the roll when the support roll begins to curl.
When the winder is running at high speed, in order to avoid vibration during high-speed operation, the design of the backup roller must be minimal when supporting the paper roll. The radius is a function expression of the speed and width of the winder, mainly by allowable The critical speed and the degree of winding are determined because at this time the diameter of the backup roll has less chance of producing a defect in the roll hardness than the small diameter support roll. When coiling coated paper or very thin paper, we should consider using a larger diameter backup roll. On a rewinder with a small width, we generally use a 600mm roll diameter.
 

Outdoor Pipeline Sealing Aluminum Coated Tape Rewinder Machine

Rewinder mechanical structure and control process ---

 

Second, the main structure of the winder

2.3 Rolling Department

3, unloader
Nowadays, with the increase of the speed of the winder, most of the winders are equipped with unloaders, which are used to push the rolled paper rolls from the support rolls and unload them on the ground. It has many forms, the most common ones are the unwinding station and the unwinding pendulum. Its control mainly depends on air pressure or hydraulic pressure. The thief of the unwinder can be selected according to the number of operators, the size and quality of the core. The advanced foreign rewinding machine can automatically control the positioning of the mandrel and mandrel and the cutting of the paper, which can save auxiliary operation time and improve production efficiency.
4, transmission mechanism
The speed of the paper-feeding machine of the winder is generally about 15 to 40 m/min. In the process of raising the speed of the paper from low, we require the speed of the vehicle to rise, so that the paper roll can be avoided due to the fluctuation of the tension. The tightness is inconsistent. Uniform acceleration is required for breakage or shutdown. During the acceleration process, the average acceleration is usually 0.23~0.37m/s, and the acceleration time is usually 50~60s. In the braking process, the deceleration is 0.42~0.75m/s and the braking time is 40s. In order to meet the shifting requirements of the winder, most of the rewinding opportunities are driven by DC motors. In the previous rewinding system, a DC motor generally controlled two supporting rollers, and in the current rewinding machine, Development and research have started with two separate motor control rolls, which can control the speed difference between the two rolls, which is beneficial for taking up the appropriate tightness of the paper roll.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com