Jumbo Roll Double Faced 3m High Quality Double Sided Rewinding Machine With Ce

Jumbo Roll Double Faced 3m High Quality Double Sided Rewinding Machine With Ce

Rewinding Machine common fault - platen roller vibration
1. Proportional valve is unstable - cleaning proportional valve or replacing proportional valve
2. Damage to the top core bearing - Replace the bearing
3. The clearance between the support wheel and the guide rail of the core device is too large - Adjust the clearance (the core is clamped at both ends of the top core, 
and the eccentric shaft of the roller is adjusted to the gap between the roller and the guide rail is 0)
4. Guide rail wear - replace or repair the rail
5. Paper core deformation - Replace the paper core
6. The top core device supports the wheel bearing or the copper sleeve wear - replace the support wheel bearing or copper sleeve
7. The thickness of the paper is different - the production process is solved

Jumbo Roll Double Faced 3m High Quality Double Sided Rewinding Machine With Ce

Guolian High Speed ??Slitting Rewinder Technical Description ---

Third, the function introduction
1. The tension control of the eject roller consists of a tension sensor and an eject motor.
In the loop control loop, the paper take-off motor is an electric motor when unwinding, and is a brake generator during normal operation and parking.
2. The pressure control of the pressure roller is controlled by various sensors such as the take-up roller diameter detecting sensor.
Forming a closed-loop control system, there are three pre-made curves for different paper grades and different finished paper diameters for the operator to choose, and the actuator will be controlled according to these three different pressure curves.
3, between the two take-up bottom rollers, take the torque difference control method, corresponding to no
The same take-up diameter, the torque between the front and rear bottom rollers is distributed in different proportions.

Jumbo Roll Double Faced 3m High Quality Double Sided Rewinding Machine With Ce

Rewinding machine unwinding tension control system design ---

       This paper presents the design scheme of the rewinding electrical control system of the main drive for the DC motor, including the overall control scheme of the system, the control of the web unwinding tension, the control and establishment of the key quantity mathematical model and the selection of the main drive motor. type.
       Web tension control is one of the most important factors in ensuring the shape of the paper roll. The most important function of the web tension is to flatten the paper web, while the stable web tension will also avoid lateral deflection of the web. In the rewinder, the web tension is generated by the eject roller drive motor operating in the feedback brake state. The magnitude of the web tension, or the stability of the tension, lies in the control of the exit roller motor. For the tension control scheme, the control systems of domestic rewinders can be roughly divided into two categories: direct tension control scheme and indirect tension control scheme. From the control scheme, the so-called direct tension scheme uses the measured tension as the feedback signal. Compared with the given signal, the tension adjuster is used to adjust the tension. The advantage of this scheme is that the control structure is simple and the control response is rapid, but it is difficult to balance the rapidity of control response and the stability of control. The so-called indirect tension control scheme is to analyze the cause of the tension change, and compensate the main disturbance amount. If several disturbances can be controlled at the same time, good results can be achieved. Taken together, direct tension control should be combined with an indirect tension control scheme to take advantage of its fast response while avoiding other deficiencies.
       The selection of the main drive of the rewinding machine should mainly consider whether the three main aspects of the speed regulation range, power and torque of the motor meet the requirements. Of course, the cost and the coordination with the gearbox should be considered comprehensively to achieve the best cost performance. The paper gives an example of the hardware selection of the system for specific tension control requirements.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com