Tape Large Rewinder Machine

Tape Large Rewinder Machine

Rewinding Machine common fault - platen roller vibration
1. Proportional valve is unstable - cleaning proportional valve or replacing proportional valve
2. Damage to the top core bearing - Replace the bearing
3. The clearance between the support wheel and the guide rail of the core device is too large - Adjust the clearance (the core is clamped at both ends of the top core, 
and the eccentric shaft of the roller is adjusted to the gap between the roller and the guide rail is 0)
4. Guide rail wear - replace or repair the rail
5. Paper core deformation - Replace the paper core
6. The top core device supports the wheel bearing or the copper sleeve wear - replace the support wheel bearing or copper sleeve
7. The thickness of the paper is different - the production process is solved

Tape Large Rewinder Machine

Design and application of constant tension and load distribution control for winder---

2Rewinder control research status at home and abroad
Rewinding machine is an important papermaking machine. It is usually installed behind the paper machine. Its speed should be 2-3 times of the speed of the paper machine, generally 1500-1800m/min, up to 300om/min. When threading, run at a maximum speed of 1:100. In order to ensure continuous paper and loose paper during the rewinding process, the tension of the paper web must be kept constant; in order to ensure the tight and loose quality inside the finished paper, the load distribution of the front and rear bottom roller motors must be performed. Therefore, the main performance requirements of the rewinder for the electric drive system are long-term linear speed, adjustable speed and wide speed range, and fast response.
The control of the early rewinder is mainly based on DC drive, and the DC control system is composed of discrete components or analog regulators to realize the above control functions. Since the transmission of analog signals requires a one-to-one physical connection, the signal changes slowly, which increases the overhead of computer speed and accuracy, and the anti-interference ability of signal transmission is poor, and paper breakage and wrinkling often occur in the production process. So in the mid-to-late 1980s, the analog regulator was replaced by a digital regulator, and the DC digital control system of the winder appeared. This control system is more stable, reliable and suitable for maintenance than the analog system, and is more suitable for interface with the factory computer. In the mid-1990s, most of the newly-invested rewinders in the domestic paper industry used all-digital DC-speed converters produced abroad, and the more famous ones were the 6RA7O series from Siemens and the 590 series DC-speed converters from Continental Transmission.
Due to the DC motor commutator and the brush, under the stable conditions, the design speed of the winder can only reach 1800m/mni, and the accuracy of the digital regulator is still limited to about 0.08% of the maximum speed, which can not meet the high speed paper. The matching requirements of the machine (the speed of the winder should be 2-3 times the speed of the paper machine). In the early 1980s, European and Japanese developed AC variable frequency speed control devices. This technology was successfully introduced to the United States in the mid-1980s and used in rewinders. The biggest advantage of the AC drive is that the AC motor is simple in construction and reliable in operation, and it requires much less maintenance and repair than DC motors.
 

Tape Large Rewinder Machine

Belt rewinding machine design and working principle ---

5:Unloading table action
1- Unloading table rise position
2- Middle position of the unloader
The unloading station transfers the paper roll from the winder to the ground.
Construction
The unloader is a device mounted on the floor to remove the paper roll. The platform is controlled by a hydraulic cylinder. The platform is a steel structure. The platform hydraulic unit is equipped with a load relief valve. These are to ensure the control process of the unloading roll.
working principle 
When the paper roll is advanced onto the platform in the upper position, the platform unloads the paper roll to the intermediate position and then onto the floor, and the paper roll rolls off the platform. For safety reasons, the platform will not automatically unload paper onto the floor unless it is moved by the operator from the intermediate position to the unloading position. The reel cannot be unloaded to the floor anyway before the new rewind.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com