Paper Roll Rewinding Machine

Paper Roll Rewinding Machine

Rewinding Machine common fault - Paper roll end faces are not aligned
1. Top core movement - Check the top core plane bearing and lock nut and adjust the clearance.
2. The top core force is not enough - check the air motor.

 

Paper Roll Rewinding Machine

Rewinding Machine operation safety regulations - 

Second, the operation steps:

7. When the layers of paper are completely flat and enter the rewinding, the waste coils are taken out to the normal production state. 8, check the production situation:
(1) Check whether the two ends of the base paper are symmetrical. For example, the auger can adjust the auger on the unloading frame to the ends of the paper. (2) Check whether the punched paper is clear, the punching is not clear or the missing teeth are checked. Whether the knife is broken or not
Whether the wire is loose, adjust the height of the bottom knife, and mass production after inspection;
(3) Check whether the paper feeding tension of the rewinding paper is consistent, keep the paper surface flat and no wrinkles, such as inconsistency
Then adjust the paper return belt hand wheel on the paper exit frame;
(4) Check whether the paper between the embossing stick and the winding area is flat and tight, if it meets the requirements, if it does not meet the requirements,
Then adjust the gearbox handwheel (when adjusting the gearbox handwheel, you can't stop the adjustment, you need to turn it on slowly); (5) Check whether the semi-finished paper roll is tight, the diameter and weight meet the product standard requirements, and the two ends are neat (straight
The deviation of the diameter shall not exceed ±1mm, and the weight deviation shall be within ±2);
(6) Whether the width of the glue seal of the paper ball meets the standard (package standard is 10mm-15mm), the penetration of glue
No more than 3 single-layer papers;
(7) Do not arbitrarily tamper with the inverter, programmed wiring and settings in the electric box; (8) Non-operator operators must not let the machine operate without the consent of the supervisor;

Third,. After the above steps are checked normally, Slowly speed up to normal operation.

Paper Roll Rewinding Machine

Rewinder mechanical structure and control process ---

Third, the rewinding machine control performance indicators
The rewinder is the last process in the papermaking process. The performance of the rewinder determines the quality of the finished paper roll. A complete rewinder must have the following properties:
1. Adjusting mechanism of pressure of the platen roller
As the rewinder continuously performs rewinding, the diameter of the finished paper roll is gradually increased, and the weight of the finished paper roll is also gradually increasing, so that the contact points of the finished paper roll with the front and rear bottom rolls are also changing. So you can come to a conclusion like this:
If the pressure of the platen roller is kept constant and does not change, the pressure between the contact points of the finished paper roll and the front and rear bottom rolls is not guaranteed to be constant, and the change in the contact point causes the pressure generated between them to change accordingly. Therefore, if we want the paper roll to reach the best form, we must adjust the pressure exerted by the platen roller to compensate for the influence of the above two factors. Only in this way can the pressure between the front and rear bottom rollers and the finished paper roll be guaranteed. Variety.
2, support roller torque program control In the rewinding process of the finished paper roll, in order to obtain high quality finished paper roll, the speed control or the support roller torque should meet certain conditions, if the speed control is used, the support roller The speed between the two should be less than 0.2%. As the diameter of the paper roll increases, the speed of the two supporting rollers must be close. Only in this way can the high quality finished paper roll be rewinded, but some quick checking systems cannot consider this design. 

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com