Roll To Roll Rewinding

Roll To Roll Rewinding

Rewinding Machine common fault - Paper roll end faces are not aligned
1. Top core movement - Check the top core plane bearing and lock nut and adjust the clearance.
2. The top core force is not enough - check the air motor.

 

Roll To Roll Rewinding

Four release and one rewinding machine operation program ---

6. Check if the power indicator on the outside of the tension control cabinet is lit.
7. In the touch screen, you need to input or rewrite the following parameters:
1 counting length is cleared (if it is necessary to re-measure the length);
2 automatic acceleration speed (refers to the speed we reach after the automatic acceleration of the machine after pressing the acceleration button delay)
3 Automatic acceleration time (refers to the time required for the machine to automatically accelerate from zero speed to the design of the highest machine speed. The shorter the time setting, the faster the acceleration.)
8. Tension control: Set the tension of each discharge motor in the touch screen. The discharge motor mainly provides a reverse torque, generates tension on the paper surface, keeps the paper web flat, and the speed control of the discharge motor is a process of gradually increasing speed, but the line speed remains unchanged.
9. Each console has its own power switch, which can be switched on and off as needed.
10. The forward and reverse running buttons are set on the console, and the user can select the running direction according to the needs.
 

Roll To Roll Rewinding

Guolian High Speed ??Slitting Rewinder Technical Description ---

The specific technical structure is described as follows:

2. Paper cutting department:
It is mainly composed of independent frame, guiding paper-feeding roller, segmented and extended arc roller device, front and rear segment guide roller, bottom knife device, round knife device and paper suction fan.
The frame is welded by steel plates and is heavy and sturdy, completely independent of the take-up frame, avoiding the effects of possible vibration on the paper cut.
Guided paper roller, diameter Φ700mm, material Q235, directly driven by motor, chrome-plated surface, hydraulic disc brake and vertical adjustment device, can be adjusted along the scale with worm gear system to adjust the tension of the paper web, adjustment range It is ±25mm. The large diameter guide rollers also facilitate smooth and high speed operation of the equipment and paper web. The bottom knife device, the round knife device and the front and rear segment guide rollers form a paper cutting platform to ensure that the width direction of the paper cutting is even and even. There are 6 sets of cutters, top knife φ180mm, bottom knife φ200mm, each bottom knife is driven by a variable frequency motor, the cutter is automatically positioned, and the cutting servo width is automatically adjusted by the control servo system. The entire slitting system assembly (including tool holders, guide rails, etc.) is imported from abroad to ensure its stability and reliability. The segment guide roller before and after the cutter has a diameter of φ198mm and a roller material Q235, which is divided into 5 sections. Each side of the cutter is equipped with SKF bearings. The surface of the roller body is grooved and the surface is chrome-plated. The circular knife device is composed of a cylinder, a sliding seat and a round knife, and is fixed on the circular beam beam guide rail. The feeding knife and the knife are controlled by the cylinder. After the starting, the two sides of the knife start to cut the paper edge, and the other round knife is given by the operator. After the command is fed, when the paper breaks, the air source of the middle circular knife is automatically cut off by the main control command and automatically raised. There is a web stabilizer plate on each side of the knife to guide the paper edge.
      Before the paper cutting table, a set of segmented stretching roller system is installed. The diameter of the stretching roller is φ198mm, the material of the roller body is Q235, and the surface is chrome-plated. The total length is 19 segments. The curvature of the multi-stage roller can be adjusted before and after the hand wheel to ensure the paper web. smooth.
      The suction paper edge device on both sides of the longitudinal cutter uses a special fan to break the paper edge, which makes the suction effect better, and is also beneficial to the next processing of the waste paper edge. Fan motor power 37KW air volume 11000m3 / h.

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com