Adhesive Tape Log Roll Rewinding Machine

Adhesive Tape Log Roll Rewinding Machine

Rewinding Machine common fault - The platen roller does not move
1. Proportional valve is unstable. - Clean the proportional valve or replace the proportional valve to adjust the amplification signal.
2. Control failure - on-site debugging of the instrument.

Adhesive Tape Log Roll Rewinding Machine

Rewinding machine unwinding tension control system design ---

       This paper presents the design scheme of the rewinding electrical control system of the main drive for the DC motor, including the overall control scheme of the system, the control of the web unwinding tension, the control and establishment of the key quantity mathematical model and the selection of the main drive motor. type.
       Web tension control is one of the most important factors in ensuring the shape of the paper roll. The most important function of the web tension is to flatten the paper web, while the stable web tension will also avoid lateral deflection of the web. In the rewinder, the web tension is generated by the eject roller drive motor operating in the feedback brake state. The magnitude of the web tension, or the stability of the tension, lies in the control of the exit roller motor. For the tension control scheme, the control systems of domestic rewinders can be roughly divided into two categories: direct tension control scheme and indirect tension control scheme. From the control scheme, the so-called direct tension scheme uses the measured tension as the feedback signal. Compared with the given signal, the tension adjuster is used to adjust the tension. The advantage of this scheme is that the control structure is simple and the control response is rapid, but it is difficult to balance the rapidity of control response and the stability of control. The so-called indirect tension control scheme is to analyze the cause of the tension change, and compensate the main disturbance amount. If several disturbances can be controlled at the same time, good results can be achieved. Taken together, direct tension control should be combined with an indirect tension control scheme to take advantage of its fast response while avoiding other deficiencies.
       The selection of the main drive of the rewinding machine should mainly consider whether the three main aspects of the speed regulation range, power and torque of the motor meet the requirements. Of course, the cost and the coordination with the gearbox should be considered comprehensively to achieve the best cost performance. The paper gives an example of the hardware selection of the system for specific tension control requirements.

Adhesive Tape Log Roll Rewinding Machine

Belt rewinding machine design and working principle ---

rear bottom roller

The movable beam is fixed to the frame. The movement of the platen roller beam moves with the hydraulic cylinder attached to the beam. The platen roller is decoupled from the hydraulic cylinder during the rewinding process. The platen roller also includes a pressure sensor to measure the pressure between the platen roller and the frame.
The platen roller has a position measuring device for providing a position about the platen roller and the diameter of the paper roll. Based on the above information, the hydraulic cylinder moves in accordance with the separation design curve as the diameter of the paper roll continues to increase. The hydraulic cylinder is equipped with a hydraulic hose rupture protection valve to prevent the paper roll from suddenly falling when the hose is damaged.
working principle 
The platen roller provides additional load to the paper roll at the beginning of the rewinding. At a later stage of the rewind, the pressure is released. In the final stage, the platen roller ensures that the paper roll is in place.
During the threading and changing process, the platen roller is raised to the rear of the safety lock at the top position. The safety lock prevents the platen roller from suddenly falling when the device malfunctions. The platen roller is automatically decompressed when the platen roller is lowered to the core or the base. If the lowering control is terminated before decompression, the platen roller will be activated and the platen roller will be raised to the upper position.
During the rewinding process, the contact surface between the platen roller and the paper core must be carefully observed. If the platen roller is very close to the core, special care must be taken during the rewinding process. If the core starts to vibrate, the speed must be lowered immediately. There is a vibration indicator on the pressing roller beam to facilitate speed reduction in that case.


Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?