Auto Rewinding Various Electric Bopp Tape Foil Machine

Auto Rewinding Various Electric Bopp Tape Foil Machine

Rewinding Machine common fault - The platen roller does not move
1. Proportional valve is unstable. - Clean the proportional valve or replace the proportional valve to adjust the amplification signal.
2. Control failure - on-site debugging of the instrument.

Auto Rewinding Various Electric Bopp Tape Foil Machine

Automatic rewinding machine speed ratio adjustment method ---

3. Adjust the curved shaft behind the punching knife. The curved shaft is finally stretched as a smooth transition axis before the web is wound up. The position of the position and the working arc size not only affect the smoothness of the paper web, but also affect the stability of the web transport. When the curved axis is too high, the paper web is scratched by the punching surface knife, and the jitter is large and the paper is easy to break. When the position is too low, the paper web is scraped to the low hole and the broken layer is easy to break. Generally, the height of the curved shaft position is adjusted so that when the paper web passes through the punching knife, the bottom layer is preferably 5~8 mm higher than the punching bottom knife, and the working arc of the curved shaft is as small as possible, and the paper can not wrinkle.
 

Auto Rewinding Various Electric Bopp Tape Foil Machine

Belt rewinding machine design and working principle ---

3. Platen roller power:
A motor that drives the platen roller by a timing belt drive is mounted on the platen roller beam. The coupling between the individual bearings of the platen roller ensures that the speed of each combined reel is the same. The speed of each part of the platen roller is the same during operation.
Platen roller photocell:
There is a photocell at the end of the platen roller beam. If the paper or any other obstacle enters the photocell illumination area, the photocell signal will immediately stop the downward movement of the platen roller. During operation, the photocell's monitoring paper does not wrap around the platen roller. If something happens, the photoelectric signal activates the alarm to stop the rewind.
Core device:
1-trache
2- top core head
3- drive motor
4- positioning stop pin
5- Safety lock in the top core lock
The core between the drums is locked before the rewinding process begins. Keep the paper roll in place during the running of the paper core locking process.
Construction
The core lock device includes a paper core plug, a cone, and a sleeve. The core of the paper core is fixed in a core seat that can be vertically up and down and can reduce friction. The core of the paper core is supported by the upper bearing of the cone, so it rotates freely. The locking of the core and the upward movement of the core locking device are done hydraulically. The vertically moving hydraulic cylinder supports the weight of the core collet so that the home can rise as the diameter of the paper roll increases. The change in the slit width is adjusted with the help of the hydraulic transfer knob. The paper core collet has a relatively low position on the locating pin. As the paper core model changes, the latch and the paper roll chuck must change. The core collet structure has a shock absorber that is lowered onto the positioning stop pin at the core of the paper core. The safety lock has a compressed air cylinder open.
working principle 
Before the rewinding begins, the collet is knocked into the paper core. The locking cylinder of the operating side core collet has a locking pressure that is less than the drive side. If the core is too long, the operating side cylinder will retract. As the size of the paper roll continues to increase, the paper core collet moves with the paper roll, preventing the paper roll from moving laterally.
Before the paper roll is pushed away from the winder, the paper core chuck is unlocked and moved to the upper position. The appropriateness of the width of the paper core collet is related to the cutter positioning device. The sensor mounted in the paper core chuck records the pulse as the spool rotates. These pulse signals are not used to calculate the paper roll diameter. There is a sensor in each side of the cone. If one side of the sensor is damaged, the other side can be used immediately.
 

About

Zhengzhou EAST IMPORT AND EXPORT co., ltd . ( a goulian group of company) a manufacturer and exporter for all kind of packaging machinery , like bopp tape coating machines, bopp tape slitting machines. Bopp tape core cutter, bopp tape core loader etc

Got any Questions?
CALL US NOW

+86-17744612788

gl006@guolianjixie.com